MG-Cars.net

Welcome to our resource for MG Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG Midget and Sprite Technical - windsrceen wiper sweep

Hi All,
I hope some one out there knows the answer to this problem. I have just fitted a round bodied wiper motor that I had in stock. I dont know from where. It over sweeps the windscreen so that it comes over the windscreen rubber by an inch at each end of the sweep. I vaguely remember that there are different quadrants within the wiper body Is this the case and can I change it or better still modify the one I have got. Thanks for any help with this infuriating niggle. Simon
s page

There are different cogs for inside the motor body.
The number of degrees sweep is noted on the large white cog.
Some one will come by shortly and tell us what number is std.

Or i could try and find the book it is in.
Or you could buy is as it is aparantley writen by one of our favorit forum members ;)
Onno Könemann

If you take the plate cover off the motor to expose the large gear wheel, it should have the degrees of sweep marked on it. According to Brown & Gammons web site, the midget should have gear no. 608092A, and according to the Minispares web site, this is a 110 degree sweep and should have 46 teeth. New wheels are available for about 25. You can't alter the sweep without changing this wheel. I believe they are made in various sweep angles from 90 to about 125 degrees.

Actually I'm surprised it is as much as 110 degrees. I think the mgb roadster is only 105, although the MGBGT is more like 120.
Mike Howlett

Simon,
If when you check under the wiper motor plate, you find that it has a 110 stamped drive wheel, then the other possibility is that you have it matched with the wrong wiper spindle wheelboxes. There were two variations of these which superficially look the same but have different numbers of teeth. The correct ones should have 32 teeth, part no 72775A - at least for the 1275 cars.

I use a 120 degree crank wheel as it gives a better sweep with slight blade overlap which avoids leaving a little gap in the centre of the screen. And they don't hit the rubbers at the ends of the sweep.
Guy

Have you got the correct wiper blades fitted? If they are too long, they will hit the rubber at the end of the upsweep.
Dave O'Neill 2

I replaced the 110 deg gear in my motor with a 130 deg to maximise the area of sweep as shown below. Availabe from SVC [and probably others].

Ref Guy's note about the wheelbox

From the MGOC website

Wiper wheel box 37H7738
Later 1275 and all 1500 models with Lucas 14W type 'Round Body' motor (G-AN4-60460 on; G-AN5; G-AN6; H-AN9-72041 on; H-AN10; A-AN10)

Wiper wheel box 37H6316
Early 1275 models with Lucas DR3A type 'Square Body' motor (to G-AN4-60459; to H-AN9-72040)

HTH



Doug Plumb

Hi Onno, Simon knows all about the book because his car is in it. Maybe he has sold his copies on ebay?

105 for US 3 wiper cars, 110 UK cars, 120 for more sweep - page 139 of the edition with colour photos..
Daniel Thirteen-Twelve

Daniel
you see your plan worked!
you did your sales pitch so manny times it conditioned me to do the same ;)
Onno Könemann

This thread was discussed between 13/02/2011 and 14/02/2011

MG Midget and Sprite Technical index

This thread is from the archive. The Live MG Midget and Sprite Technical BBS is active now.