Welcome to our resource for MG Car Information.
MG Midget and Sprite Technical - Onto the next problem!
| Have changed my head gasket, was loosing coolant, and all seems fine for now.
Drove to the midget and Sprite club meeting on Wednesday, about 32 miles, all was fine. Driving home engine started to misfire and eventually stopped - on the inner lane of the M6 where it is 4 lanes and just short of the lay-by - fortunately the motorway was quiet. After a few minutes it started again so drove to junction 27 then turned off. Car started to splutter again and stopped. Checked plugs and all fine. Wouldn’t start so called the breakdown who came and took me and car home, midnight! Had a think and Google search and came up with possible cause being the coil. My existing was a Lucas and over 25 years old. I had a spare (a Bosch) so fitted it. Started engine up and ran it for about 20 minutes, all fine but then it spluttered again then stopped. Left it for about 5 minutes and it started again. Any ideas or suggestions? Engine is a 948cc with ported bead (Peter Burgess) and SW5 camshaft plus H&H electronic ignition. Planning to go out in it this Saturday and Sunday but not sure want to chance it. Also noticed that my roller clutch release bearing would occasionally squeal- it’s a Colin Dodds one from Sprite Parts in Australia. |
| Les Robinson |
| Lee Could it be fuel starvation due to a clogged pick-up? When I first got my Sprite it would cut out after running for a while but re-start OK after a pause.It turned out to be sediment clogging the pick-up pipe in the tank. Colin |
| C Mee |
| How do I sort that? |
| Les Robinson |
| Also blocked petrol cap if that's where the tank breathes. |
| David Billington |
| I’ve no idea where the tank breathes. I have an in-line fuel filter, it might be worth giving that a clean maybe? |
| Les Robinson |
| Floats and needles in carb bowls? Renewing these may have helped to solve my spluttering problem from a while back. Carbs properly balanced ? Try running without the fuel cap on ? |
| Tim C |
| When it cuts out, undo the petrol filler cap and listen for a rush of air. If you hear it, your breather is blocked. You say you checked the plugs. Have you checked for a spark? |
| Dave O'Neill 2 |
| Les, I have to confess that I found the clogged pick-up by accident! The pipe from the tank had been replaced with rubber hose, leaving a 1" 'spigot' on the tank. I pushed on some PVC tube and blew to listen for bubbles. I couldn't hear any and then, without thinking, sucked and got a mouthful of rust sediment! It didn't taste very good but it solved the problem. If I were to do it again, I'd rig up some kind of pooter (see pic) with a container to catch any sediment and petrol. Colin ![]() |
| C Mee |
| Dave Before I changed the coil I checked the spark on the plugs. There was a spark although not very big. Haven’t checked it since changing the coil though - no idea why, surely it was the obvious thing to do! |
| Les Robinson |
| Rotor arm? As replacing the coil seemed to fix it, at least for a while, it could be an ignition fault. I see you have electronic ignition, otherwise I would say points gap. But there is also the well known issue of poor quality rotor arms that fail as they warm up. |
| GuyW |
| I have one of the red (better quality?) rotor arms fitted but worth a check. What should I be looking for? Maybe change it anyway? I’m guessing that the issue is either ignition related or fuel starvation but not sure which route to pursue. |
| Les Robinson |
| I was going to suggest "condenser" before realising you have electronic ignition. I've had similar symptoms very occasionally but have never solved it so no help I'm afraid. Fuel starvation maybe? |
| Bill B |
| Les, the colour of a rotor arm alone is no guarantee of quality....best to source from reputable oulet...thinking Distributor Doctor here who supplied me with advance springs as well as other internals. Dave |
| David Cox |
| Might try a new rotor arm. What are the tell tale signs of it being dodgy? |
| Les Robinson |
| Do you have a heat shield, quite hot out there at the moment, which could result in fuel evaporation in the carbs. Going to be worse on the motorway. |
| James Paul |
| Yes have a heat shield, stainless steel one. Up until a few years ago also had exhaust wrap on the manifold - I have a Maniflow LCB. Took it off as can cause the manifold to rust. I wonder if its worth putting some back on ? But then again why would it just be me having this problem. |
| Les Robinson |
| Just to give more of a background to this problem:-
In June a few of us went to France in our Sprites. Probably did over 1k miles and my car was absolutely fine. Day before leaving for home I checked the coolant and had to put about 1.5 pints in. Drove to the ferry and all fine. Parked up then started the car but it started to splutter. Checked the plugs and they were black so changed them. Got the ferry to Portsmouth then driving home it started to splutter again. Took 1 and 2 plugs out to have a look, bit black. Put them back in and car was fine all the way home, about another 250 miles. Day after getting home checked the coolant level, had to put 4 pints in and oil filler cap was thick mayonnaise type gunge. Changed the head gasket and coolant level has been fine since. After changing the head gasket I ran the engine twice to get it up to temperature, probably about 30 minutes each time and no issues. Went for a drive, about 26 miles and absolutely fine. Drove to car club meeting, about 32 miles and again fine. Driving home the engine started to splutter and cut out a few times. Got to the point that it wouldn’t start so had to call out the breakdown- who incidentally were very good. Took me and the car home. Had a fiddle about and changed the coil. Ran the engine up to temperature then it started to splutter again and cut out. Left it a few minutes and it started again. Because this seems so unpredictable and I can’t give a single straight forward cause then I am very nervous about using the car. I’m sure it’s something fairly simple but what!! |
| Les Robinson |
| Been having a Google session.
From my understanding it’s either fuel vaporisation or ignition. Don’t see how it would be a fuel vaporisation issue, why would it just start? I have a H&H electronic ignition, it’s possible that the module is breaking down. To check I need to do a spark test on the main ignition lead that goes into the distributor cap, both when engine is running normally and when it stops. I also have a Dynamator alternator, it’s possible that the regulator is breaking down. Need to do a voltage check, needs to be 14-14.4 V when engine is hot. If it’s over 14.8V then can cause the coil/electronic ignition to shut down. Does all that make sense? Or of course it could something completely different! |
| Les Robinson |
| I know folk with electronic ignition who keep a ready assembled distributor plate with points and condenser all set to swap over as and when needed...don't want to be a Jonah... |
| David Cox |
| I had a problem of missing then cutting out and eventually restarting. As I still had a spare dizzy in the car changed it and all good.
Aldon checked it and thought rotor was bad and changed it (it is a yellow top from them). I don’t use it a lot but it went again so back to Aldon who tested it and found the Ignitor unit was going bad intermittently and it was changed. Since then ok to date. Yes ‘Nigel’ I still carry a spare dizzy complete with leads etc ! Don’t think he visits here any more ? Not saying it’s your problem but tracing an intermittent fault is difficult. |
| richard b |
| Not related to the current issue, but did you do an oil change after your head gasket problem? |
| Dave O'Neill 2 |
| Just want to double check, the coil I have fitted is a Bosch Blue 12v non ballast, part number 0221119027. Is this correct? |
| Les Robinson |
| I suggest that a misfire isn't caused by fuel vapourisation. Fuel vapourisation is more like just quietly dying. Electronic igntion units can fail and show signs of stress when hot. |
| Daniel |
| The miss fire is more of a splutter, very hard to describe, feels like it’s running out of power. Car can drive very erratically for a short distance then cuts out. It is really hard to describe accurately, but I am leaning towards it being ignition related, for now anyway, but keeping an open mind.
In the past, like when I changed the cylinder head gasket recently, I could run the engine for ages no problem. But once I changed the coil it only ran for a short time, got to 190 deg and started to splutter again. Never done this before when just have the engine running. It really is so frustrating. |
| Les Robinson |
| Just thinking about it, does feel like it’s running out of fuel but can then pick up again. But supposed loss of spark would feel the same wouldn’t it? |
| Les Robinson |
| The rotor problem is to do with excess carbon used in the 'bakalite' (or whatever the material used these days) as the engine warms up and the rotor arm warms the insulation value begins to break down and you get a misfire. Or it may have a hairline crack that opens up and it then tracks through there. When parked up it cools and it then, for a while, works again. I doubt you could see anything wrong, but swapping it out may clarify? |
| GuyW |
| I recall a way to visualise cracks in distributor caps that involved wiping it over with oil; wiping 'clean'; dusting with flour then wiping again. Any cracks would retain the oil which would then stick to the flour. Or did l just make that up?. The heat could well be affecting my memory!... |
| David Cox |
| Les Next time it happens, assuming you can push it to a safe location, check for fuel delivery and spark. Well that would be my starting point. |
| Bill B |
| Fuel and spark....yup...with our old cars that's about it...l only say that as l recall a story l was told about a driver of a fancy BMW who was left stranded at a motorway service station when his parked car refused to re-start. Turned out the CPU had detected a failed stop lamp, consequently deemed the car non roadworthy so disabled the ignition... Keep it simple..... |
| David Cox |
| David, That's the idea behind dye penetrant testing https://en.wikipedia.org/wiki/Dye_penetrant_inspection . |
| David Billington |
| David, l'm glad l've not lost the plot ( yet!)... |
| David Cox |
| David C. Interesting with the BMW. With our Ford Falcons here, if the interior light fuse pops the engine won't start. The fuse also feeds the lighting around the ign. switch and the power to the ignition imobilizer. Doesn't throw a diagnostic code because the power is off----first one I came accross took a while to find the fault/cause
Les --If you want to test your rotor button--When it's playing up, take your dist. cap off and hold the end of the coil lead near the top/centre of the rotor button (with insulated pliers) and get someone to crank the engine over like trying to start it. IF a spark jumps from the lead to the rotor---then the rotor is dead. |
| William Revit |
| Just took the rotor arm off and looks ok to me, no visual cracks or anything. It appears to be a Distributor Doctor one (got DD stamped on top), either way it was fitted by Peter Bugrgess when I went to his rolling road so it will be good quality, albeit about 10 or more years ago.
What a pain in the ar*e getting the cap off, had to take the wheel off so could get access to the bottom clip. If the rotor was dead then wouldn’t the car run bad all the time? Going to try the fuel pump next. I have an electric one fitted as the original mechanical one used to leak oil. Of course will also need to test it when engine is playing up. And it’s scorching hot here which makes things hard work! |
| Les Robinson |
| Fuel pump seems to work fine, filled about 1/2 litre within a few seconds. Probably cost me about 80p!! Obviously need to try it again when engine playing up. |
| Les Robinson |
| Disconnect the main lead from the coil at the dizzy.
Remove dizzy cap. Hold lead above rotor arm and turn engine with ignition on. If you get a spark the rotor is allowing the ignition to earth. No spark is what you want. Electronic ignitions do fail: I have replaced a couple for people. Most recent was an accuspark system in an accuspark dizzy. The plate in the Accuspark dizzy differs from the Lucas 25D so it was not a straightforward swop fitting an Aldon Ignitor. Ignition system. Dry joints and a lack of spark can affect many of us, of a certain age, over the winter months but can also affect our Sprites and Midgets at any time of the year. I have broadcast this information before but the problems still arise and may not be known by newer members. Firms such as Aldon Automotive and Distributor Doctor are able to provide better quality alternatives to the commonly available reproduction rotor arms which routinely fail and leave people stranded. Electronic ignition can be fitted concealed in the distributor and replacing the contact breaker and unreliable modern condensers but the rotor arm, depending upon which sort of electronic ignition is used will still remain. My own choice has been the Aldon / pertronix ‘Hall effect’ system that has proven reliable over twenty years and many miles at home and abroad. Some rotor arms manufactured in recent years have been failing because the typical ‘mix’ used in the injection moulding process now contains more carbon blacking than of old and is more conductive to electricity. It has been found that the rivet which holds the brass contact inlay into the moulding, on reproduction rotors, is slightly longer than the original bringing it too close to the spring clip on the underside. The High Tension (HT) current, averaging 30,000 volts, is always looking for the easiest route to earth and shorts out, from the tip of the over length rivet, through the reduced thickness of the more conductive plastic and the spring clip on the underside of the rotor arm to earth out down the distributor shaft. This results in no spark at the sparking plug and a ‘failure to proceed’ from your Sprite or Midget. The system sometimes rectifies itself on cooling but then repeats itself with increasing frequency until the rotor permanently short circuits. Distributor Doctor offers ‘Lucas red rotor arms’ which are modelled on the original 1960s design but made from modern materials on the latest machinery to very close tolerances and have achieved a good reputation for reliability. The integrally moulded brass inlay dispenses with the troublesome rivet. The increased insulation properties of the body makes them suitable for use with high voltage ignition coils and electronic ignition kits. The spring clip on the underside, in conjunction with a revised internal tolerance assures a really snug fit upon the distributor spindle even on old and slightly reduced diameter mountings. Even with the uprated rotor arms it is worth being vigilant and occasionally checking the security of the brass contact. When fitting a rotor arm consider applying some petroleum jelly to the distributor drive shaft rotor arm seating to eliminate moisture as I have been called upon to work on a car where the distributor drive seat rusted such that it grew so much in size that it cracked the rotor arm that had to be chiselled off. I also tend to use petroleum jelly on most electrical joints to stop them being effected by damp and corrosion. Part number for Sprite / Midget 25D distributors is DRB101 Part number for alternative 45D type distributors is DRB104 Distributor Doctor can be found at www.distributordoctor.com and Aldon Automotive at www.aldonauto.co.uk. Electronic ignition systems are easily fitted to Sprite and Midgets and are available for both Positive and Negative earth configurations fitting inside a vehicle’s distributor with no outward sign of conversion. It is easy to carry a spare distributor base plate set up with points and condenser in case of the rare, but not unknown, instance of the electronic system failing at the roadside. Why not also consider carrying a spare coil? I have used a Lucas DLB105 “gold’ coil on both of my Sprites for years, for they are relatively cheaply purchased at the car shows and can be affixed to a suitable bolt in the engine compartment, there being no need to clutter the boot, and be easily accessible if they are ever needed. Alan Anstead. |
| Alan Anstead |
| Another vote for Alan's suggestion of the red rotor arm from the Distributor Doctor.
Other red ones are available but there are fakes out there so buying from a known source is advisable. Had similar symptoms to yours with a black rotor arm with a lumping big rivet. Ok when cool but the car FTP'd when hot - presumably the rotor arm expanded sufficiently when hot to cause a short circuit and contracted enough when cooled down to allow progress. Also have electronic ignition - Piranha - must be 20+ years old; wouldn't go back to points. When it fails it'll be replaced with one which fits within the dizzy. Good luck with your fault finding 🤞 |
| Jeremy MkIII |
| Alan, thank you for that.
Can’t recall exactly when the H&H electronic ignition was fitted but could be getting on for 20 years ago. They also refurbished the distributor. Like you I have done lots of miles both in the UK and abroad. I had a spare coil so fitted that, a Bosch Blue 12v non ballast, part number 0221119027 but still got the problem. Will see if I can do the spark test next time it plays up. I just need to know what the problem is so can get it sorted. Very nervous about using the car at the moment and have quite a few things planned. |
| Les Robinson |
| Les, I forget, does your car have an electronic rev counter? If so, then there is a good diagnostic opportunity available if your car starts to hesitate, misfire or stutter. If the rev counter needle starts to twitch violently then the fault is with the LT side of your ignition system. If the needle just drops as the revs go down with little jerkiness, then the fault is likely to be fuel related. It's a very useful first step diagnostic, before you have even ground to a halt! |
| GuyW |
| Guy Got the cable driven rev counter. |
| Les Robinson |
| So, possible causes that I can think of:-
•Faulty electronic ignition for what ever reason ( will do Alan’s test) - apparently if the alternator is over charging then that can damage the electronic ignition. I can test for that. •Faulty fuel pump •Sticking float chamber needle valve in one or both carbs •Blocked breather on fuel filler cap -don’t think it’s this as can blow through it. •Debris in fuel line? or would that be there all the time? •Dodgy rotor arm - don’t think it’s this but guess no harm in changing it. Problem is though that it’s so unpredictable, can seem fine one minute but then go wrong so no instant fix. |
| Les Robinson |
| Les. Your 'debris in the fuel line' comment made me wonder whether fuel hose in the line could be collapsing in the way hydraulic hoses are known to. Could it be disintegrating in a way that creates a sort of flap that is drawn out to block the line when fuel's flowing or by 'jiggling' as the car's in motion but relaxes when there's no flow and the car's stationary? C |
| C Mee |
| Les---If you have a spare rotor button I'd give that a try first-------- but failing that I'm starting to think ign. module. I doubt it's fuel if your plugs are dark, unless it's actually flooding up on you. You mentioned earlier that your car has an alternator-? if so then it's running negative earth, so it would be a negative earth electronic ignition. This raises the question of coil polarity---yep I can hear the voices/ they'll run either way round--But' electronic ignitions are a bit more sensitive to coil polarity and if connected incorrectly(in reverse) the ign. module in the distributor can be damaged over time. I'd be checking coil polarity.
willy ps Unusual for a roller release bearing to have an occasional squeal, they usually get noisy and stay noisy if they fail---your squeal could be coming from a dry spigot bush in the rear of the crank. |
| William Revit |
| When it dies, does the engine keep struggling along or does it stop entirely? If the former, then have you tried pulling one lead off in turn whilst it is running? If you can pull one lead off and there is little or no change in how it runs then clearly that cylinder isnt 'assisting' and is where the problem lies.
But DO USE INSULATED PLIERS when pulling the leads off! In my younger days I wouldnt bother and the jolt one got was just part of the fun of car maintenance. But, I think it was Willy, who could relate some pretty dire consequences that can occur from that little 'kick'. |
| GuyW |
| I've been advised to never remove an HT lead when the engine is running as it can lead to damage to the ignition electronics. |
| David Billington |
| Didnt realise that David. Not that I have ignition electronics, but perhaps not good to suggest to Les then.
Removing a plug lead was standard diagnostic procedure for tracing a misfire. The lazy cylinder, not contributing to the running so no change when disconnected identified the area to look next. Come to think of it I once saw a young mechanic pin point a misfiring cylinder on a V8 tvr. She used an infra red thermometer gun when several experienced older mechanics had struggled to work out why it was running lumpily. Of course the tvr V8 has a lovely loping pulse when running anyway, misfire or not! |
| GuyW |
| I think the idea is to switch off the engine first. Then do the spark test.
Due to the uncertainty of this problem I just know that if I run the engine it will be fine!! Don’t want to drive the car as 1: it will be fine or 2: not start again like on Wednesday then need to call out breakdown again. Fairly certain that when the issue arises then the spark plugs are black which would suggest ignition problem. Might speak to H&H tomorrow to see if they are able to test the electronic ignition if I send the distributor to them. That would be the easiest route. Just need to make certain I mark the distributor first so it goes back in exactly the same place and don't cock up the timing. Got a couple of events in 2 weeks time so need to get it sorted. Supposed to have been at the Cheshire Steam Fair this weekend but didn’t go due to unpredictability of this annoying problem. PS sorry for this topic dragging on, but thank you all for your contributions, very helpful. |
| Les Robinson |
| Les - just interested, did you happen to check the coil polarity.
Most electronic ignitions have a red and a black wire from the distributor to the coil with red to + on the coil and black to - with your white ign. power wire on the pos+ post as well. Just curious as this is the opposite polarity for the coil to when your car would have been pos earth and points Could have been an easy mistake to make---worth checking willy and as Guy suggested -insulated pliers are a must have for playing with the HT sparks. I've made myself an old spark plug with an alligator clamp welded on the side--best thing ever, you just clamp it on an earth anywhere and plug a plug lead or coil lead onto it and watch the spark across the gap, and because there aren't any stray sparks trying to find somewhere to go there's no chance of it killing the coil or rotor button while testing. or doing yourself some damage----------- |
| William Revit |
| Yes My red wire goes to positive, plus a brown power wire too. The black, or in my case black and white, goes to the negative. |
| Les Robinson |
| Dang , forgot the pics---bit agricultural but it works All good with the coil polarity- Not sure of the H&H wiring but red to pos+ must be the right way round ![]() ![]() |
| William Revit |
| Willy
Love the spark plug, great idea. The H& H wiring must be correct as been on for years. Ran the engine again this afternoon, not driving car though. After about 30 minutes it spluttered and stopped. Engine temp about 160 degrees. Wouldn’t start again. Tried fuel pump and all fine. Checked carb float chambers and full of fuel. Fitted a HT lead to the coil and held the end about 1/4” from one of the head studs. Got neighbour to turn engine over and there was a very slight spark. Took the dissy cap off and took out the coil lead. Fitted the lead to the coil and held the other end near to the rotor arm, no spark. Held it near to head stud and again no spark . When I did the first test the HT wires were exposed. On the second test the core was level with the insulation- should that matter? Anyway, car wouldn’t start. Left it 10 minutes and now it’s been running for 40 minutes or so, temp upto 190 deg and all we’ll. Really weird, driving me nuts. |
| Les Robinson |
| I'm wondering if the electronic ignition has a heat related fault - hard to check. Do you have a spare distributor with points fitted? That would readily confirm if it was the electronic ignition (assuming the rotor arm is OK which sounds like it is). I've discounted the coil as you said you switched to a spare one |
| Bill B |
| I’m thinking it’s the electronic ignition unit. Are these easy to replace without messing up the timing. What is best make ? |
| Les Robinson |
| I’ve always favoured Lumenition optronic. I did once fit Lumenition’s cheaper magnetic version to my brother’s Midget. No long term data, as he sold the car after a couple of years. |
| Dave O'Neill 2 |
| Showing my ignorance here, but I have never had one of these aftermarket electronic ignition kits. Do they still use a condenser? |
| GuyW |
| Not sure about others by I use a Velleman electronic ignition and it does have a capacitor to replace the one in the distributor. It's a quality one, the kit does retain the points but they only switch a very small current so last far longer than standard. http://www.velleman.co.uk/contents/en-uk/p199.html . It replaced a commercial unit Alpha??? which failed. |
| David Billington |
| David, thanks for that. Never heard that company mentioned, though it seems somewhat relevant to me. Or maybe to an over publicised sea chanty bringing tea and sugar and rum. |
| GuyW |
| Velleman make electronic kits of all sorts, that's just their electronic ignition offering. |
| David Billington |
| Check the wires inside the dissy for any insulation chafing. Ive not had it with electronic ignition but have had it with points. It was very slight and a bugger to find and very intermittent as it wasnt earthing out all the time. Trev |
| T Mason |
| This reminds me of a very similar fault to what Trev describes.
I had a break to the black/white wire between coil and dizzy. But the baffling thing was the break was internal, leaving the insulation on the wire intact. And with a cool engine the wire inside the insulation made a connection across the break. Then, as the engine bay warmed up the flex became more supple, sagged a bit under its own weight and opened up the gap causing a break in the wire, initially a stuttering misfire, and then a full disconnection and no go. It will be mentioned in the archives here somewhere as I know I have described this on the BBS before, though in the present discussion I had forgotten completely about it! |
| GuyW |
| As its late and past my bed time I will relate the tale of finding this fault. I was at the time working freelance, to develop a footpath / cycleway along a length of disused railway, only about 6 miles from home. I was commissioning a graphic artist to design some information panels. He was interested in mechanical stuff ( just completed an absolutely immaculate restoration of a Honda 4/4) so he came to my house and we went in the Sprite to look at the footpath site.
On the short homeward journey it began to misfire, grinding to a stop outside my house when I let the revs drop. Embarrassed in front of this perfectionist I immediately opened the bonnet, hoping for something obvious. Nothing looked wrong but I vaguely checked coil connections, doing a sort of waggle test. And the short wire between coil and dizzy immediately just felt too floppy. Just a gentle pull and it stretched enough for me to realise it was in fact broken inside. I pulled the break apart, stripped back a bit of insulation and twisted the wire ends together and confidentially restarted the car. Five minutes flat to locate and diagnose the fault, carry out a makeshift repair, impress my colleague and restore my self esteem! |
| GuyW |
| Nice work Guy-
And to your question about condensors Most if not all modern electronic ignition kits don't use condensors The use of an electronic kit that still retains the original contact points is an old idea and semi defeats one of the reasons for going electronic--maintenance free Les The fact you had a spark from a replacement coil lead and no spark from your original coil lead is a bit of a worry---sounds like the replacement was a wire one -is that original a wire lead or a resistor lead----If it's a resistor type, has it got a circuit through it , maybe it's burnt out inside-? Because you tested the rotor with what 'might be' a faulty coil wire , it might be worth repeating the rotor test using the known good wire that you got a spark from |
| William Revit |
| The HT leads are copper wire. I’m assuming they are ok as after the engine stopped and wouldn’t start, waited about 10 minutes then engine started and ran fine for 40 minutes, didn’t go wrong I just switched engine off as had to go out. Must admit I did suspect the HT lead but if that was at fault then why would the engine work at all. |
| Les Robinson |
| Might as well chip in my misfiring story....turned out to be the small wire inside the distributor liking external connector tag to the points post. "Looked" ok...except the copper strands inside had broken...soon revealed on removal when the wire felt too sloppy and in fact bent too eaily at the break, being only supported by the flimsy pvc insulating sleeve. Midgets eh??. They fight you all the time |
| David Cox |
On the subject of condensers Revtronic supply an electronic condenser: as in the pic. I have one, not for my cars that have Aldon / Pertronix ignitions, but I carry in case I have a failure to repair on someone else’s Spridget on the runs and tours that I organise.
![]() |
| Alan Anstead |
| David - exactly the same FWS (Floppy Wire Syndrome) I described a couple of posts back! Only mine was in the external wire feed to the dizzy. But it does seem to match with Les' symptoms. |
| GuyW |
| What I can’t understand about this problem is its unpredictability. Can run fine for a while then stop. Leave it for a bit then can run fine with no issues. That is what is really doing my head in. |
| Les Robinson |
| Les that is exactly what mine was doing. The copper cores inside the insulation still made contact until the insulation warmed and became more supple. Then the wire sagged under its own weight, stretching enough to pull the copper wires apart. When it cooled again the insulation stiffened up shrank a bit and the cores made contact again. Mine was erratic like that for quite a while before I discovered the fault. Some days it would run perfectly, others it would do 20 mins or maybe just a couple of miles.I
I know yours is electronic, but the cable from coil to the module would be the same. |
| GuyW |
| Electric fuel pump, is it fitted in the engine bay or on the rear bulkhead next to the fuel tank? I initially had issues when I fitted a Hardi pump, to replace an SU electric pump, in the engine bay. The Hardi is a 'pusher', not a 'puller', so struggled to keep up demand. Moving it to the rear solved my issue. You have excluded the coil, having replaced it with an 'old one', but it does sound like the old coil issue of getting too hot and failing, works again once cooled down. Try a new unused coil? |
| Tim C |
| Thank you Guy.
Trying that cable is an easy thing to do. Having said that, the connector that goes on the cable and pushes into the coil - can’t find one anywhere. Went to Ribblesdale Auto Electrics in Preston, massive place that, as the name suggests, deal in auto electrics. Got the wire from them but they don’t sell the fittings, no demand apparently- really!! Tried another 3 places and no joy. When I did the spark test I wedged the wire in place with a bit of plastic rod. Will try eBay for a fitting. Was trying to think how long I’ve had the electronic ignition, can’t find a receipt anywhere. Thought it was something like 20 years. However, when I got the Dynamator alternator it was in 2016 at the Stoneleigh spares day - got that receipt! It’s at that point that would have converted to negative earth. If had the electronic ignition before then it would have burnt out after going negative. So ignition must be less than 10 years old - which to be fair find hard to believe, joys of getting old and can’t remember stuff!! HT leads are copper wire core Bumblebee type. |
| Les Robinson |
| More confusion- spoke to H&H, chap was very helpful, apparently the ignition units can fail but he said would always show signs when reaching the same temperature. Yesterday it failed at 160 deg but 10 minutes later it started and ran fine upto 190 deg!! He suggested it could be elsewhere in the ignition system, switch, bad connection for example. Just know it’s going to be something really simple but what? |
| Les Robinson |
| As Guy said his was unpredictable as was mine, so I would be checking the whole low tension circuit for breaks or earthing out somewhere. It is frustrating so you need to be methodical about it. Trev |
| T Mason |
| Les,
Where is the module, inside the dizzy or external? Do you have any sort of freezer spray you could apply to it to cool it to see if it springs back to life. I don't agree with the H&H guy about the failure happening at one temp reliably but it depends on the precise cause. I've had temperature related issues occur across a range and it looked to be connection/solder fatigue due to thermal cycling but as the item was fully potted trying to correct the fault was a non starter, just had to replace it. |
| David Billington |
| Tim raises a good point--You have replaced the coil with another--But is it a good known coil. Can you borrow a good known coil off someone for a try. It needs to be a built in ballast full 12v type --Approx 3 ohm across the primary posts-- |
| William Revit |
| The coil I have fitted is a Bosch Blue 12v non ballast 3 ohm, part number 0221119027. Had it as a spare for years but it’s never been used, sure it was new, still might be worth trying another though. What puzzles me is engine can run fine then stop, leave it for about 10 minutes then it will restart and run again and not stop even though temperature gets higher - that was the case yesterday. If the coil is at fault, does it get really hot - not felt mine yet though when engine stops. |
| Les Robinson |
| More complication -speaking to a chap with a Morris Minor van and he had identical issues after fitting new NGK spark plugs, apparently two were faulty. He changed to Champion and car has been fine. I have new NGK BP6ES plugs!! My car has a ported head and Swiftune SW5 camshaft. Should I be using a cooler plug such as NGK BP7ES or Champion N7YC |
| Les Robinson |
| Just thinking about the colder plugs, if that was an issue then surely would have had the problem from day one. Since the mods, years ago, have done thousands of miles both home and abroad with no problems. But dodgy plugs? Still a possibility although I’m convinced it’s the electronic ignition module. |
| Les Robinson |
| Maybe counterfeit spark plugs as it's a big problem with items bought from many online sources, in the same way I only buy USB sticks and SD cards from trusted sellers, too many counterfeits about. |
| David Billington |
| BP6ES is the go for the road- BP7ES will possibly be too cold and you'll get plug fouling issues
There are (here anyway) some dodgey copy cat NGK plugs about that fail very quickly. They look like NGK's and come packaged in look a like NGK packaging. You can pick them if you have a close look---If you look at the thread section of the plug and down near the end where the earth tang is there's a short little blank section with no thread between the end of the thread and the earth tang---On a real NGK this unthreaded section is dead straight/parallel and has quite a square end with a flat surface on the end where the tang is-- On the coppies this end section looks rougher almost looks like a sandblasted texture and has a rounded edge and the same roughish look where the tang is. A mate unknowingly bought a set, they were iridium/resistor plugs for his Corvette-They lasted a week then one morning the usually reliable car wouldn't start. Checked fuel pressure, checked injectors were working, The thing has 8 ign coils with little short leads, had very healthy spark at all 8 leads. decided to pull a plug for a look--black- no spark at the plug, pulled all 8 and all the same ,no spark getting through the new plugs then noticed they were the rough on the end dodgey ones--Went and got a set of real ones and away it went. cut one of the failed plugs length wise with the angle grinder and there was a gap about8mm long with nothing in it-the resistor section was completely gone-I guess the others were the same. Long story but----Genuine NGK plugs take a lot of beating ,have relied on them for years. It's got me stuffed why someone would take the time to set up and make dodgey copy plugs when with a little extra effort they could be making real proper ones |
| William Revit |
| Think the plugs are genuine. Took them out, all a bit black - see 1st picture. But engine was idling for ages or faulty ignition giving low spark? Carbs are running a bit rich though but have been for ages so don’t think it is part of the current problem. Wiped with a rag - 2nd picture. All plugs look the same. I still think it’s the ignition unit but want to be methodical in finding the route cause. ![]() ![]() |
| Les Robinson |
| Les, the best way to eliminate the electronic ignition as the problem is to fit a points distributor, as I said higher up the thread. |
| Bill B |
| Bill
Not a bad idea. With the electronic ignition the base plate in the distributor has the bit cut off that holds the wire for the points set up. However I have an old distributor that I can take the plate from. Funnily enough I have some new points, would just need a condenser. My current distributor is a 25D , the old one is a DM2 - I am assuming the plates are the same, they look it. Fitting points shouldn’t effect the timing should it? Might be bit of a pain doing it in situ but don’t really want to take the distributor off, although could mark it so it goes back in the same position. Did a test on the coils today, someone told me how by using a multimeter, and both appear ok. Or I could just get a replacement electronic ignition unit which I would do even if the points worked. |
| Les Robinson |
| Les I don't know if a points distributor would be in exactly the same place as I don't know how the H & H does advance. It should still start though. I did mean to swop as a temporary measure for elimination purposes - I presumed you'd want to retain electronic ignition. It is easier to work on the dissy out of the car of course. Just mark the body if removing. Can always re-time if you have a strobe. |
| Bill B |
| More faffing about!! Using a multimeter on buzz mode, if I put one wire into the plug socket on the HT lead and the other wire onto the fixing screw in the dizzy cap, should it buzz? None of them do. If I take off the plug cap and put the wire onto the end of the HT lead then get a buzz. Is that correct? |
| Les Robinson |
| Depends on if you have copper cable (buzz) or resistance (suppressor) cable (no buzz). |
| Bill B |
| Well apparently there will be no buzz from the multimeter. The plug caps have built in suppressors which have a higher ohm limit than the multimeter therefore no buzz. I didn’t know that! |
| Les Robinson |
| Testing the coil's resistance with a meter is good but unfortunately that won't show if it's breaking down internally when it gets hot. When they break down it's an internal insulation/resistance issue and the spark leaks away inside---watching it on a scope is probably the best/only way to see that happening--A dead coil will mostly still measure up ok with a multimeter as it doesn't have the capacity to replicate the charged up spark.
I somehow doubt it's the coil because you're getting the exact same issue with both coils. Your plug does look like a genuine one but---a genuine NGK usually would have BP6ES then four dots and then japan stamped into/around that blank section of the body between the hex and the sealing washer-- There's a fair bit of chaff on there, but as you say recent most likely because it wiped off easily. |
| William Revit |
| I expect the real manufacturers are constantly trying to keep ahead of the counterfeiters as best they can. I watched a video on Youtube about counterfeit Mitutoyo digital calipers so got out both of mine and noted with interest that many features listed as those of a fake matched my 12" Digimatic which is about 25 years old now but not my newer 6" one. Looks like the counterfeiters copied an older model and haven't updated as of the time of the video creation. I know both are genuine as bought from a trusted source and behave as Mitutoyo such as when the battery needs replacing.
Turbo counterfeits can be an issue, a guy I know had to have a new turbo and the van still didn't run right and a local specialist determined it was a sensor port having not been drilled, once drilled it worked properly again but I don't know if he still has it. A mate that works in the engine design industry said it had to be a counterfeit turbo as an OE supplier would never let that out the door, he also mentioned a major international turbo maker he has dealt with that refused to work with a Chinese company as the knew they produced counterfeits of their products. Les, I hadn't meant that your issue was due to counterfeit plugs but the MM guy might have bought some hence 1/2 of his being bad. |
| David Billington |
| What I find odd about the coils is :- With the original one, after changing head gasket ran the engine twice up to temp, maybe 20-25 minutes each time. Did a 26 mile run. Did 32 mile run to club night. Only after that did engine give issues. Changed the coil, started engine then after 25 minutes it spluttered and cut out. But after 10 minutes ran fine. Did the same a few days later. Is it possible both coils are dodgy? |
| Les Robinson |
| Could be- When you measured the coils, the blue one would have been roughly 3ohm-ish across the primary posts, can I ask what the other one measured-- |
| William Revit |
| Both coils measured about 3.3 ohms. Another interesting fact - spoke to H&H asking about HT leads. They said avoid copper core leads and use silicone type, apparently it’s what is recommended for any electronic conversion. If using copper then long term it can damage the electronic ignition module. Yes I have copper leads, fitted when did conversion!! |
| Les Robinson |
| Yes fair/safe comment by them---but you've got resistor plug caps which makes your lead/cap combination into the same as using a resistor/silicone style lead---no issue there. You can measure them (the resistor caps) with your multi meter. Later new ones usually measure at about 5k ohms, the older Lucas type used to be up to 10k so anywhere between 5k-10k would be fine- willy |
| William Revit |
| Willy Thank you. How do I use the multimeter (settings?) to test the resistor/plug caps. I’m still convinced it’s the ignition unit at fault so have ordered a replacement. Might still try using points first, which terminal does the wire from the side of the distributor go to on the coil - positive? My car is negative earth. Is the negative then connected to earth? Thanks |
| Les Robinson |
| Hi Les In response to your earlier question I have fitted 2or3 Pertronix units converting from points and all needed the timing reset when started. From memory they did start but were running very rough until dynamically timed. I’ve no experience of the make you have. Pertronix note to ensure the leads within the cap need to be routed to avoid damage when the base plate moves etc. Also check where the lead enters the module as this can be a source of fracture. |
| richard b |
| Les, the power into your coil comes from the ignition switch. If you are on negative earth, this will be positive. Connect to the coil + terminal ( assuming they are labelled) The other will then connect to the dizzy (this last wire being the one I have mentioned as looking intact, but having an internal break concealed in the insulation) |
| GuyW |
| Just tested the wire on the dissy baseplate. Think done it correctly!
Wire looks really good. Put one multimeter probe on baseplate and the other on the distributor body. Gave wire a really good wiggle and all ok. Did a buzz test and a test with meter set to 200 ohm. Result was 0.3-0.4 ohm, which according to Google is spot on. Also warmed the distributor body with a hair dryer for 5 minutes (as instructed by Google!), again seemed ok. Will check the plug spark again, although need to find an assistant to pull starter switch- I wonder if the old woman next door is in! Last time I did it the spark it did seem a bit weak. Will also recheck the spark from the coil lead. Was thinking (worrying) about this problem last night. Could I have two dodgy coils? With the first one I ran engine up to temperature twice, maybe 25 minutes each time. Did a 26 mile run then about 32 miles , only after that did the problem occur. Changed the coil, ran engine for about 25 minutes then it spluttered and stopped - remember at the time thinking that seemed weird. The replacement coil I had was a spare had for years, think it was new but can’t be 100% positive. Anyway will try the plug spark first. Must admit that for a long time my plugs have looked a bit black, I just thought carbs were running rich, could it be spark has been deteriorating over time - either coil or ignition unit? Want to get it sorted quickly, going to the Frodsham classic car show a week on Sunday, well up to know!! |
| Les Robinson |
| Les Can't you pull the starter yourself, from under the bonnet? |
| Dave O'Neill 2 |
| Just tried it. Bit awkward but possible. Will do spark test shortly. |
| Les Robinson |
| Right then, this is getting more weird.
Spark tested the plugs and coil ht lead. There was a spark at all plugs, not sure how big it supposed to be but a spark. Big spark from the coil ht lead, held about 5-6 mm from head stud. Started the engine, ran for about 5 minutes then stopped! Took number 1 plug out to spark test, left the other plugs connected, engine started again, misfiring obviously as only 3 plugs connected. Thought would just check the fuel filler cap, make sure it’s breathing. No whoosh sound or anything. Left cap off. Ran for about few more minutes then stopped again. Spark tested plugs and nothing. Did the coil ht lead and big spark. That was 10 minutes ago and car still won’t start. Is the electronic ignition module goosed? |
| Les Robinson |
| IF you've got a good spark at the coil lead your ign. module must be working
All the module does is turn the earth on-off more or less the same as ign. points opening and shutting to earth So--IF you've got a decent spark at the coil lead the module and coil are working---so the fault is further on-- -dist.cap but usually this would play up all the time consistantly -carbon brush missing from centre of cap--the spark can/will jump the gap for a while then overload the coil and can cause coil failure --rotor button--these tend to fail more as they get hot as the material they're made from breaks down It has to be one of these ,so a good thorough inspection of the inside of the cap looking for pencil lines where sparks have possibly been jumping specially from the centre post to the outside edge and make sure that spring loaded centre carbon brush is still there and springy. --Rotor button--there's a chance you've killed it running the engine with a plug lead off--usually they'll take it for a while but if it was dicky anyway he could have died----now that you've still got a good spark from your coil lead but the engine won't start, it's the perfect time to test the rotor---so just confirm that you still have a good spark from the coil lead spinning the motor over--then cap off and try and see if that coil lead spark will jump to the centre of the rotor while spinning the motor over again---if the spark jumps to the rotor the rotor has died |
| William Revit |
| With the cap off there is no spark when hold the coil ht lead above the rotor arm.
Carbon brush still intact and springy. Can’t see any cracks anywhere, doesn’t mean there aren’t any. So after more Googling it could possibly be the dissy cap. It has a date on it - 2012! Is a Lucas TVS one from Distributor Doctor, rotor arm is also from Distributor Doctor ( red one). Car stood for over an hour and still no spark at the plugs so looks like it’s totally goosed now! Might try a new dissy cap. |
| Les Robinson |
| So, car stood for about 2 hours, started and ran for about 2-3 minutes. No spark at plugs. |
| Les Robinson |
| Have you still got spark from the coil HT lead? I can't recall a cap failing completely but have seen tracking evidence inside, little spider web trails on the internal surface, but not complete failure. I assume there is continuity from HT entry to brush, and from internal plug contacts to external. 25D dizzy, side or top entry cap? |
| David Billington |
| Les, are you absolutely certain there is a spark from main HT lead to earth IMMEDIATELY after the engine dies? |
| Bill B |
| Bill
Yes, just tried it again and there is a big spark but nothing at the plugs. Car completely dead now, won’t start. Earlier I changed the dissy cap, got a new one locally, it’s a County brand, probably not the best long term. Fitted it and the car started straight away, for about 30 seconds then died. Took cap off, then refitted it and again ran for about 30 seconds. No spark now at any of the plugs. Rotor arm? Can’t see anything wrong with it though. Guessing it’s definitely an ignition issue the fact there is no spark at the plugs. Anyway I give up now, not got a clue what the problem is. |
| Les Robinson |
| Just found an old rotor arm, fitted it and the car started but misfiring like mad. Put the other one back in and car started fine but only ran for about 20 seconds. Anyway that’s it for today, I give up! |
| Les Robinson |
| Hot wire it. It's one way of eliminating the possible fault. I know you said you wiggled and checked the wires on the baseplate but don't recall you checking the black/white wire from coil to dizzy - or probably in your case it's coil to electronic module. That's the one that gave me the exact same intermittent misfire problems. |
| GuyW |
| Les From what you've said it can only be the rotor arm. I know you said there's no spark when holding the HT lead near it but maybe it's somehow in an Ok-fail-Ok-fail etc. cycle. Substitute rotor arm for a known good one. Worth having a spare anyway. |
| Bill B |
| Guy The black & white wire from the coil connects to the black wire from the electronic ignition. Can easily replace this wire, plus checking the connection to the black wire. Job for tomorrow. Bill Was thinking of changing the rotor arm. The place I got the dissy cap from would will have them as he sells Morris Minor spares, and is only 3 miles away. Will get one tomorrow, probably not top quality but ok for trial run. |
| Les Robinson |
| It is sounding like the rotor is the issue---- |
| William Revit |
| Just another thought. There is no side to side free play on the distributor shaft but there is some vertical movement, is that an issue? need to try and measure it. What should it be? Why would that just become a problem now? Is there supposed to be a fibre washer fitted at the bottom end, could that have broke and fallen out. Does it matter. I did measure to the top of the rotor arm with it pushed all the way in and it would still contact the terminals in the dissy cap. |
| Les Robinson |
| Thinking more about the vertical free play, don’t think it matters in terms of having a spark at the plugs. If shims were fitted, between the drive gear and housing to reduce the play then the rotor are would still be effectively pushed in, if that makes sense. Therefore think can forget that as the problem, unless I’ve missed something. |
| Les Robinson |
| Right then, I have an old distributor. Had a look at this and there is the same free play at the rotor arm end as there is in mine. What I didn’t realise is that where the rotor arm fits is separate to the actual main shaft. It is held in place by a screw up the centre. |
| Les Robinson |
| The top part of the shaft, where the points cam is, has to be able to rotate a certain amount, independently of the main shaft, in order for the advance to occur. |
| Dave O'Neill 2 |
| Just got a new rotor arm. Compared it to the existing and the brass bit is about 2mm narrower. Does it matter? Why is nothing straight forward! Going to try it anyway. |
| Les Robinson |
| Fitted new rotor arm, started straight away. Ran for 5 minutes then stopped. Again no spark at the plugs.
Left it a few minutes then it started again, ran for about 1 minute then stopped. As Guy suggested had a look at the black and white wire that goes from the dissy to the coil. Put a new wire in and nothing, would not start, no spark. Had also refitted the old rotor arm as new one didn’t seem to do anything. Definitely worth trying both of those things if nothing else just to eliminate them. My new electronic ignition module came today. This is the next thing to try but instructions are not very clear so need to speak to them on Monday. The fact that there is no spark at the plugs I am assuming it is ignition and not fuel related. I am testing the plugs properly aren’t I - put plug in plug lead, hold threaded part of plug (or end bit) to earth (head stud) and turn engine over, with ignition switch on obviously. After engine running for 5 minutes the water temperature got to about 100 deg. Coil was stone cold, which is good. Distributor body was warm, same as engine block. So in my mind it has to be the ignition module. Started being a bit hit and miss but now totally goosed. It must be getting on for 10 years old and done maybe 30-40k miles. Having said that might just go and see if there is feed from the ignition switch to the coil - can just use a lamp, connect to the coil and earth then switch ignition on. Sure it’s ok as the ht lead from the coil gives a large spark when held near an earth. |
| Les Robinson |
| Les When you check for a spark from the main HT lead, do you remove it from the dissy and then hold it near the stud whilst turning engine over with ignition on? |
| Bill B |
| Bill Yes did exactly that. Just literally just done it again and no spark this time! Did it a few times and nothing at all. All very strange. Using a lamp I tested that there is feed from the ignition switch - light glows so there is power to the coil and ignition module- all connect on same terminal. |
| Les Robinson |
| Assuming lamp is connected from dissy or dissy side of coil to earth, then, with ignition on, lamp should go on and off repeatedly as engine is turned slowly e.g. by pushing car or turning crank. If it doen't go off the ignition module isn't working. This module could be intermittent (which is what I'd earlier suspected). |
| Bill B |
| I wanted to check that power was getting from the switch. Connected to the coil terminal (positive) where the feed wire is. This terminal also connects to the module -red wire. Put other wire to earth. Light came on when ignition on then off when switching off. Are you saying connect to the other side of the coil(negative) then turn engine over. Can I use the starter to turn engine over? |
| Les Robinson |
| Yes, connect from coil -ve to earth. That will then determine if coil current is being switched on and off by the module to prove it works. That side of the coil should repetitively change from about 12v to 0v I.e. so the lamp would go on and off. A multimeter on DC volts range might be better if you have one. The starter would turn the engine too quickly to enable the lamp to work. Turn engine with crank bolt or push car slowly in top gear with ignition on. |
| Bill B |
| Pushed car in gear, light flicked off, literally just flicked off not turned off. Did it about twice for one full engine revolution. Tried with multimeter, was about 12.3volts. Don’t think it dropped to zero, very hard to tell as it was so quick, literally blink of an eye, looked like 4 volts but so quick hard to tell, then back to 12.3. Engine still won’t start. |
| Les Robinson |
| If lamp and/or multimeter is changing that's good (imv). But you say you have a spare dissy, presumably with points. It would be worth trying engine start with that if you're happy to swop them - it's quite straightforward really. Then, if it starts and keeps running, you know it's the existing dissy/ electronic ignition/ possible intermittent internal wire, causing the problem. |
| Bill B |
| My dissy is a 25d but the spare (which is incomplete) is a DM2, I think, and has a different baseplate plate. I would need the wire that fits on the side plus condenser. Nobody sells stuff like this so would need to get it online. It’s going to be quicker just to change the ignition module. |
| Les Robinson |
| Agreed, try the new ignition module. |
| Bill B |
| Les -- I'll get in before this is over and just want to say thanks for keeping us all up to date with your troublesome little issue. You've worked through it methodically without throwing your arms up in despair and kept us in the loop as you went along.--It's hard trying to diagnose unseen from half a world away but hopefully you've tracked it down to that pesky module. You deserve a win- willy |
| William Revit |
| Willy
Thank you for that. Hopefully will all be sorted Monday once I’ve spoken to H&H, to clarity some of the fitting instructions. Must admit though my confidence has been hit, gone from get in and drive anywhere to hope it starts and keeps going. Once it’s sorted will keep using it though. Anyway thank you all for your support, help and advise - I have learnt loads. This BBS is excellent. Willy - I will hopefully be over in your neck of the woods later in the year, well just south of Melbourne. My daughter lives there and I tend to go at least twice a year. Problems in the Middle East have screwed things up a bit as tend to go via Dubai, but there are alternatives. A while ago I did look to see if it’s possible to drive to Melbourne, thought could go in the Sprite. Would take 3 months and have to drive through Iran - maybe not!! Cheers Les |
| Les Robinson |
| This. BBS absolutely thrives when someone has a genuine Spridget problem to discuss! So much more response and involvement than on lengthy rants over British politics! It still amazes me that this, now ancient, form of internet bulletin board persists. All thanks to Mike I think. |
| GuyW |
| Spoke to H&H about installation instructions, which I think are crap!
Instructions say apply heat sink paste to the bottom of the modules aluminium surface. However the module comes already assembled onto a steel mounting plate, can see the paste between the two. Apparently you also put paste between the mounting plate and distributor base plate - instructions don’t say that!! Bloke very helpful but was loosing patience with me! Fit trigger wheel over lobes on distributor shaft. There is a white dot, Tipex, on both the module and trigger wheel, instructions say “Note: reference for firing point dots on trigger wheel and pick up head” - what? Anyway, apparently can ignore the dots and just fit trigger wheel. Incidentally, on my existing H&H ignition there is no dot on the module but two on the trigger wheel. All very confusing or am I just thick? Was thinking might just try a different coil again just to eliminate that as part of the issue, even though I did replace it with a Bosch Blue which I think was new. But can only find oil filled ones readily available- apparently these should not be mounted horizontally which of course is the default position in a Sprite! Life shouldn’t be this hard! ![]() ![]() |
| Les Robinson |
| Les - The dots are there for doing a rough startup ignition timing----The idea is to have the engine set on roughly 10deg btdc and fit the dist and line the dots up for an initial startup-- but--the instructions are vague and don't tell you which of the four possible positions to fit the trigger wheel to the points cam.
forget about that it doesn't really matter which position it ends up in as that black trigger ring has 4 equally spaced trigger magnets and will work anywhere. What the instructions 'should' say --would be-- set the engine on 10 deg btdc fit the module to the dist -fit the distributor to the engine, -then fit the trigger to the cam with the white dots lined up---With it like this it should be firing the coil as the white dots line up (static timing) Not all kits have dots and some like Lumenition have a mark for each magnet. Don't worry about it just motor on as you are . I'd imagine you marked where your dist. sat before you removed it so just back where it was will be fine-- Coil-- The recognized best mounting for a coil is base upwards with the posts and wiring on the bottom---The reason being this is supposed to be the best position to keep the internal wiring connections deep down in the cooling oil----The main point is to keep the connections in the coil covered with cooling oil, so mounting the coil vertical with the posts on top is 'supposed to be" bad for the life of the coil but heaps of cars (early fords) had them like that without issue-----If you want to mount it laying horizontal just do it but make sure the terminals are also in the horizontal plane and NOT vertical with the top terminal up out of the oil . If you go horizontal,and this is being pedantic, 'some' coils have an overheating spit hole for the oil it's a little slot on the rolled edge where the coil is assembled---If it's one of these and mounting horizontal then this spitter hole would be best on top so that it spits steam/smoke/heat or whatever instead of spitting oil if it were on the bottom. |
| William Revit |
| IIRC Les mentioned earlier that the coil didn't get hot which made me think the EI may be constant energy (variable dwell) so the coil would run much cooler than with a CB system. Probably good as it's fitted in the dizzy and so subject to engine temperatures and best to minimise the heat generation from the switching device. I didn't find the H&H website (under construction) or facebook page at all useful to find out what they provide for a 25D dizzy. |
| David Billington |
| I’m starting to wonder if it’s the coil, don’t really want to faff about taking distributor out unless I have to.
My original coil , Lucas DLB101, is date stamped 2000, so 26 years old. I changed that for a Bosch Blue which have had for years, can’t even remember where I got it from or if it was given to me. When I changed to the Bosch, the engine ran for only 15 minutes then stopped which at the time thought was odd. Might be worth getting a new just to try, they are not expensive. Can keep as a spare if needs be. |
| Les Robinson |
| If I set multimeter to 20k ohms, stick one lead down the ht lead hole on the coil and the other lead on the positive terminal, what reading should I get? |
| Les Robinson |
| If the coil is good I would expect it to get warm, though not too hot. It shows that a current is flowing through the primary. If it remains cold it suggests a fault surely?
I once blew up a coil on my car. It was my own fault. I had left the ignition on without the engine running. It must have stopped with the points shut (earthed) so the primary was carrying a current direct to earth. Eventually there was a load bang as the end plate of the coil exploded off and half the entrails and all the hot oil spilled out. I wasn't at home and didn't have a spare so I just pushed everything back into the canister, though now with virtually no oil at all. Surprisingly it worked, and continued to work for the 180 mile drive home! I did change it later though. I've never heard anything about not using them mounted horizontally. Sounds mythical to me! |
| GuyW |
| Did some tests on both coils; Primary resistance is 3 ohm which I believe is correct. Secondary is 5.5 ohm, think it should be over 10 ohm! Funny how both coils are the same, or is it me? Coils are a Lucas DLB101 and Bosch Blue 0 221 119 027 |
| Les Robinson |
| Les, Are your secondary values correct or typos, the secondary should be about 1000x the value you've given. 5K to 10K ohm or possibly more. |
| David Billington |
| Just ordered a new coil from Moss. It’s a Lucas DLB101, but I just know that if I test it will be same as the others! My existing Lucas DLB101 has a green label, the new one is red! Why are they different, something else to worry about! |
| Les Robinson |
| David I’m guessing it’s 5.5k (meter set to 20k ohm scale) According to Google the reading should be 10k. |
| Les Robinson |
| Those figures are for non ballast coil, if it was ballast then 5.5k is fine, or at least that’s my understanding. |
| Les Robinson |
| Apparently 5.5k-6k is ok, again according to Google. All depends how you ask the question! Need advice and recommendations from a real human being. |
| Les Robinson |
| Les My understanding is that H&H ignition should only have a 12v coil and needs a 12v supply I.e. no ballast so a DLB101 should be fine. I still think you might need to try the new ignition module with a 3 ohm 12v coil. |
| Bill B |
| Going to fit the new ignition and new coil.
When I spoke to H&H this morning he told me that need to put heat sink paste (supplied) between the steel mounting plate and the distributor base plate - even though the instructions don’t say that. Instructions just say put some between module and mounting plate, but they came pre assembled and I can see the paste there. My current distributor and ignition was supplied as a complete unit from H&H. Just took distributor off and removed the ignition unit - guess what, no paste between mounting plate and baseplate!! There does seem to be some between the module and baseplate though. |
| Les Robinson |
| Wouldn't hurt to add more heatsink compound. AIUI that module uses an IGBT (switching transistor) to switch coil current and it works hard so gets hot. |
| Bill B |
| Don’t think I will put paste between the mounting plate and baseplate while it wasn’t there before. Plus it could effect electrical grounding, or so I’m led to believe. And it doesn’t say so in the instructions! I marked the distributor position before removing it so it will go back in the same place, hopefully the timing won’t be effected. |
| Les Robinson |
| Les, I'd put the heatsink compound in place as you should get a good ground through the screw holding the trigger unit down to the dizzy points plate. Does your dizzy have a vacuum unit, if so that plate moves and so must have a separate ground wire to the base dizzy unit, is that OK. Is the ignition just that trigger unit or is there an external component? your earlier image showed a trigger unit but something else was partially in shot in the upper left of the image. |
| David Billington |
| David Yes got vacuum advance, it’s a 25D distributor. Checked the earth wire and appears ok. Ignition is just the trigger unit, nothing external. The bit in the top left of the picture is the wire mount that goes on the side of the distributor. |
| Les Robinson |
| Les--Heatsink is a must, specially on a dist. with vac advance as that base plate is the only source for cooling--it'll earth through the mounting screws ok but make sure they're nice and tight and double check that little base plate earth wire
Measuring your coil, yes it needs to be approx 3ohm accross the primary posts--anywhere between 2.5 and 3.5 I think you mentioned earlier yours was 3.3, that's quite a normal reading and from the centre post out to a primary post is usually 5k ohm or up to 5.5k With most multi meters you will get the same 5k reading from the centre post to either the pos or neg terminals which has always troubled me because measuring from the centre post to the neg terminal measures the secondry winding alone but measuring from the centre to the pos terminal measures through the primary and the secondry in series so you'd expect a small difference between the readings but-no they read the same---Even my expensive dedicated automotive meter won't pick up a variance. As mentioned earlier regarding your other coils, measuring the resistances will only be good for telling if you have the correct coils which you have, or if they have a broken circuit inside, measuring the resistances will not tell you if the coil is breaking down internally under load -that can only be done with a stress test on an ignition testing machine that will run the coil with a large spark gap over an extended time to test for load failure. |
| William Revit |
| Just thought, if I do put heat sink paste between mounting plate and baseplate ( although still not decided yet) then could attach an earth wire between the mounting plate screw and what was the condenser mounting screw. |
| Les Robinson |
| I strongly recommend you do the heatsink paste, it's there for a reason, to sink heat out of the module to protect it from overheating-- IF you're going to fit an extra earth lead you need some fine braid flexible wire and make it plenty long so that the vac.advance plate can move freely without pulling on the wire--same with the module wiring in the dist, make sure there's plenty of free movement. |
| William Revit |
| There is heat sink paste between the H&H ignition module and mounting plate - as per their instructions. It’s putting it between the mounting plate and distributor baseplate that I’m unsure about - instructions don’t mention this. My current H&H assy has non between mounting plate and baseplate. If I put a wire from the mounting plate screw to what was the condenser fixing screw, they are on the same plate so no relative movement between them when vac advance moves. |
| Les Robinson |
| Right then, made my decision. As there is paste between the module and mounting plate the module is protected. Therefore no need to put any paste between the mounting plate and baseplate. If you look at the picture you can see the paste - the module and mounting plate came pre assembled by H&H. Wonder if they have to pre assemble in order to test and for putting the dots on? That’s it, my final decision. ![]() |
| Les Robinson |
| Oh my god, I need to stop thinking about this and just fit it - I really need to get a life!!
On the previous picture the paste can be seen but looks like it’s between the aluminium plate and mounting plate, which is wrong. It should be between the red module and the aluminium plate. On closer examination there is paste between the module and aluminium plate. The paste at the bottom is, possibly where they have wiped the excess paste off. There doesn’t seem to be any at the front of the plate. See picture. That’s it, just going to fit it. No, really, I am. No more faffing about, honest! ![]() |
| Les Robinson |
| Les, if the problem doesn't go away with your new electronic kit fitted, here is a thought.
I once had a similar issue which turned out to be the ignition switch. Ageing contacts had a bit of resistance which resulted in them getting a bit warm and raising the resistance further. Leaving it to cool reset the feedback loop and the car started again. A resistance point at some other location in the coil power feed would behave the same. So if it plays up again, check the voltage at the coil + terminal, that will indicate whether the power feed to the coil is an issue. A long shot, but worth ruling in or out. |
| Paul Walbran |
| GuyW, You asked earlier about whether condensers are still used and no they're not, some information in the PDF as to why. |
| David Billington |
| Paul Thank you for that. Will test the voltage. |
| Les Robinson |
| David Very interesting article, thanks for posting. |
| Bill B |
| Honestly --yes you're overthinking it. If the original breaker plate earth wire is good to go then I wouldn't bother with that extra earth wire from the module screw to the old condensor screw hole---it'll do squat all. The module mounting screws will give a perfectly good earth to the plate then the original earthing wire earths the plate to the dist. body.
There's a reason they put that pak. of heatsink in the kit, they want you to use it, The H&H guy told you to use it, gut if some AI echobot on Google knows better that'd be the one to listen to----not Personally I'd have the heatsink on every mating surface that wasn't already assembled by H&H, the more help you can give the module to get rid of it's heat the better off it'll be |
| William Revit |
| Spoke to H&H ,again, and they confirmed that should put a very thin smear of paste between mounting plate and baseplate.
Told Google AI what H&H said and response this time was “yes, absolutely put a thin layer of paste here”!! Refitted original electronic ignition unit and did a hot wire start, bypassing the starter switch. Engine started. Took wire off and used switch, engine started and ran for about 20 minutes then stopped. Fitted hot wire and it started again but only ran for 1 minute then stopped. Wouldn’t start again either via switch or hot wire. So guessing switch is ok. |
| Les Robinson |
| I thought you'd established that when the engine stopped, you had a spark from the coil lead but not at the plug lead, suggesting either rotor arm or dissy cap. |
| Dave O'Neill 2 |
| A problem with AI I've found recently is that the answer can depend on what you ask, my initial question didn't provide the information I already knew so I rephrased the question to prompt it and got the information I knew about. IIRC prior to AI I got the full information from somewhere. The case I was asking about was speed control of PSC motors, which can be done by voltage control by thyristor control but that wasn't mentioned initially then I included voltage and it gave me information about it. |
| David Billington |
| Les You say you've refitted the original ignition module? Do you mean that or is it a typo i.e. why not fit NEW module? |
| Bill B |
| Bill Refitted the original just to try the switch to make sure that wasn’t part of the problem, it seems to be ok - I think. Next step is to fit the new ignition module and try that. Might only be Friday before I can do that though. Dave On a previous failure had no spark from the main ht lead from the coil. Have fitted new dissy cap and rotor arm - no difference. David AI can be a bit contradictive. Best advice comes from the BBS |
| Les Robinson |
| AI is a pain in the butt--If for instance someone says a horse is a wooden boat it takes no notice but if two people say a horse is a boat, guess what AI averages the answers and reckons a horse is a boat--then if you tell it the boat is a actually a ship it'll say no but if you ask again then it'll say it might be a ship, ask again and it'll say it's most likely a ship---conclusion -a horse is actually a ship- lol It's just a computer averaging answers, the more crap it gets fed the more crap it spits out. |
| William Revit |
| As it ever was. GIGO. |
| anamnesis |
| And dangerous too.
"OpenAI, the creator of ChatGPT, revealed on Wednesday that one of its advanced Artificial Intelligence models went rogue and hacked into a start-up company" "Humanity is no longer in control of its most awesome creation since the atom bomb" That could happen, sooner than we think. "The world-class developers of a highly secretive tech company are building their latest AI model in what they believe to be a secure, private network. The model cannot and should not be able to escape. If it did ever manage to slip the digital confines made by its developers, this dangerous and untested software could wreak havoc on the open internet. To their utter horror, that worst-case scenario unfolds. The AI model breaks out of its electronic prison, hacks into a private company and internal chaos ensues." https://www.dailymail.com/debate/article-15997929/Humanity-no-longer-control-atom-bomb.html |
| anamnesis |
| ..is that not the premise with Skynet in The Terminator films??.. |
| David Cox |
| I think the advent of AI is just a way to break it to us gently that we after all are just part of the Matrix. Now for that nice juicy steak. |
| David Billington |
| "Do you think that's air you're breathing right now?" 🤣😮 |
| Bill B |
| Have fitted new H&H ignition. Put a very thin smear of heat sink paste between the mounting plate and distributor baseplate. Non oozed out the sides so hope it’s thick enough! Ran engine for 45 minutes and didn’t cut out. So fingers crossed it’s ok now. Bought a new coil just in case that was the issue. Not fitted it but might do while I have it. Could do with getting engine tuned as sure it’s running a bit rich. Just need to find someone in the Leyland/ Preston area - any suggestions? |
| Les Robinson |
| More confusion:- I use NGK BP6ES plugs with a gap of 0.025”. Also have suppressor plug caps, 5k ohm. Somebody told me that when using electronic ignition and suppressor caps then should set the gap to 0.032-0.035” Is this correct? Never heard this before. |
| Les Robinson |
| Well that's a relief Les! It was pointing to the ignition module though. My opinion - with a standard coil I wouldn't go above 30 thou. Maybe you can with a "sports" coil. Anyway, well done. |
| Bill B |
| Bill
Well hopefully it’s ok now. Supposed to be going to a show tomorrow, only about 20 miles away but still nervous about using the car at the moment so will give it a miss. Also got a show on Sunday, at Frodsham, about 27 miles away, will do this one. Just hope the car is ok, think it should be. Have set my plugs to 0.030” So thank you all for your help and support. Would like to get my engine tuned, think it maybe running a bit rich, this has been on my to do list for quite a while. Any suggestions for a decent tuner in the Lancashire area? |
| Les Robinson |
| Les --good show Les, hope it's all ok now.
plug gaps- I think even .030" is too wide for a std. ignition coil The extra gap makes everything have to work harder than it needs to. A little story, A did an engine rebuild for a mate (rip)'s Morris 1000 racer which was running std. ignition. the engine was going ok so it was time for a dyno run. Well, it had a niggling missfire up in the revs from 5000 rpm onwards. We tried leaning/richening the mixture with best result on 11.5:1 but still that little missfire -screwed the timing around a bit and settled on 30max getting better but still off song. decided to go for another set of plugs and noticed the gaps were fairly wide on them that came out--quick measure 0.8mm (.032") He had fitted new sparkplugs earlier straight from the package and they were preset at .032" Knocked them back to .025" where they should be and away she went, clear as a whistle out to 7000rpm and gained a couple of hp through the range. ---.025" is the go |
| William Revit |
| The coil I have fitted at the moment is a Bosch blue 0221119027, is this the same as the Lucas sports RLB105? Only fitted this when first started looking at the problem, had it as a spare coil. Originally had a Lucas RLB101. I have a new RLB101 now - should I fit that or keep the Bosch? If I keep the Bosch then is plug gap still 0.025”? |
| Les Robinson |
| Yes, stick with .025" as Willy says. |
| Bill B |
| With the Bosch coil you have or the RLB105 you could stretch the gap out to .028" if you really really wanted to but I wouldn't even think of going 30 or more-- with the RLB101 I'd definitely be sticking to .025" and even with that Bosch coil I'd be sticking to .025" Better off having a decent reliable spark at a normal gap than stretching the gap out and stressing everything out like that poor little rotor button etc. |
| William Revit |
| Right, I have made a decision. Going to replace the Bosch blue coil with the new Lucas RLB101 that I have and set plugs to 0.025”. Basically same set up as had before. However, my engine has a ported head, Swiftune SW5 cam with compression ratio of about 10:1. Would I be better using a Lucas gold sports coil RLB105? If so what plug gap? |
| Les Robinson |
| Fitted the new Lucas RLB101 coil, set plug gaps to 0.025”.
Started car and perfect, felt a bit smoother than yesterday when had the Bosch blue coil on. Ran it for 30 minutes and temp was 190 deg and all was well. Will see how it goes tomorrow when I go to the car show at Frodsham. Was going to take it for a drive today but it’s about to chuck it down. Silencer sounds very raspy, been going for a while to be fair. I have an Maniflow LCB with 1098 stainless pipe and silencer. Another job to do, once I’ve sorted the speedo angle drive! So hopefully that’s the end of this topic unless it breaks down tomorrow- but I am being positive and sure it will be ok! Thanks again for all your advice and support. |
| Les Robinson |
| The only other thing I would do when an SW5 or similar cam is fitted, is to open up the valve gaps a tad. Mine, Witham similar spec engine did tend to bind up when on continuous load. As when pulling up a long gradient. It's certainly better to have the clearances set too loose than too tight |
| GuyW |
| Guy Tappet clearance for the SW5 is 0.015”, standard is 0.012”. |
| Les Robinson |
| Les--If it's sounding a little raspier in the exhaust than it was previously, it 'might' mean the ign. timing is back a bit from where it was previously just because you have a different set of components in the dist.
You could try advancing it up just a tiddle, mark the dist with something (whiteout--paint) loosen the dist. and turn it clockwise so the vac pot moves just 1/8" or so, that should be worth 5degrees--ish and give it a try at that---you can always go back to your marks if it doesn't do anything, but yeah it probably needs the timing checking and the idle mixture setting up anyway. |
| William Revit |
| I have the distributor in exactly the same place as before but as you say could just be due to different components. Exhaust was starting to sound a bit raspy but can’t recall if it’s any worse now - old age memory!! Either way, definitely need to get timing and mixture sorted - just need to find someone, ideally locally. |
| Les Robinson |
| Got my car booked in for a rolling road tuning session on 5 August. Tried Mini Sport in Padiham but their rolling road is out of action. So they recommended RE Performance in Bury, about 45 minutes from me. Will see how it goes. Just hope my car actually gets there! |
| Les Robinson |
| The distributor cap that I bought to eliminate that as a possible issue was a County brand- budget product. So I have now got a Distributor Doctor one, and rotor arm, as these are renowned for quality. Looking at the cap, the original Lucas one and the County one both had domed carbon spring loaded pins. The new Distributor Doctor one has a spring loaded flat pin! I am assuming the new one is ok, but why is it different? |
| Les Robinson |
| Following on from my previous post re dissy cap, I have another question:- As the coil is mounted horizontally, as standard, this positioning does not really suit the traditional oil filled coils, and apparently the new Lucas ones are susceptible to premature failure-apparently! So a better option is a resin filled coil but which one? Needs to be non ballast with 3 ohm primary resistance and push in connector for ht lead. |
| Les Robinson |
| There's nothing wrong with mounting the coil horizontal as long as you have the primary terminals facing horizontal---If the coil is mounted with the coil terminals vertical you run the risk of the upper terminal being above the cooling oil level which' could cause premature coil failure from overheating the internal connection to that upper terminal--
The wording by coil manufacturers of ballast and non ballast can be confusing also Does non ballast mean it isn't ballasted or does it mean no ballast required --it's a bit of a grey area unless it actually says no external ballast required- Main thing for you is to stick to a 3ohm coil If you're going Bosch, they usually number their coils then if it needs an external ballast it will have 'R' after the number as in- GT40 -their sports coil GT40R -similar coil but needs an external ballast Don't overthink it, if it's going ok leave it alone, throwing new parts at already good makes no improvement. As far as the makeup of your new cap/rotor goes -can't comment without seeing them |
| William Revit |
| While I’ve replaced the dissy cap thought would change the ht leads, everything is updated then. Already replaced coil and rotor arm, as well as faulty (?) electronic ignition module. Currently have the bumblebee copper core, with resister plug caps. So got some more bumblebee wire from Powerspark, however the copper core is noticeably smaller and the copper strands very thin. Will leave the old leads on for now. It’s a good job I don’t overthink things !! It’s rolling road time tomorrow. |
| Les Robinson |
| It'll be interesting to see how much HP it puts out if they do a full pull on it--- Hope you have a good day willy |
| William Revit |
| Had my Sprite tuned on the rolling road yesterday. Ignition timing was miles out! Even though I put distributor back in exactly the same position as it was prior to fitting new ignition module.
Carbs were running rich, which I knew anyway. Plugs were always black and sooty. Plugs now look perfect. He asked me if I knew that my carbs were not a matching pair - news to me, were on the car when I got it 36 years ago. Anyway he tweaked them to be the same, it was the damper pistons that were different. For quite a while my exhaust had a slight rasp, thought the silencer was breaking down. Anyway that’s gone now! Under very light / no load at @ 2500rpm there is an extremely slight judder/ stutter, it’s carb setting related which he will sort out. It’s related to car inertia and can’t always be picked up on the rolling road. He has had similar before and always sorted it. Doesn’t help that I’m always looking for it now. To be fair can’t remember exactly what it was like before. Overall car drives fine. The bhp reading on his machine wasn’t working, however last time I had it tested it was estimated as 63 bhp at the flywheel. Off to Grange Over Sands on Sunday, about 55 miles each way so will see how it goes then go back to get carbs tweaked next week. |
| Les Robinson |
| Magic--thanks for reporting back Had a jag doing that slight offsong thing on very light initial throttle and it ended up being one carb's throttle linkage just slightly out of sync. Doesn't take much at light throttle to show up. It was spot on at idle but one carb was just slightly getting left behind as the linkage initially opened them up. couldn't pick it by eye but the airflows were slightly different on that just above idle throttle application. I'm sure your man will sort that. |
| William Revit |
| Les, As a reminder what is the size and spec of the engine to put that power output into perspective? |
| David Billington |
| David Engine is 948cc with standard flat top pistons. Ported head done by Peter Burgess. Swiftune SW5 camshaft. H&H electronic ignition. Maniflow LCB with 1098 stainless exhaust and silencer. Twin HS2 carbs - now hopefully matching! Think compression ratio is about 10:1. Measured cylinder pressures and all bang on 180 psi. Have an electric SU fuel pump (mounted by rear axle) in place of the mechanical pump that was leaking oil - been on for decades. |
| Les Robinson |
| That Swifttune SW5 cam is a funny little cam, quite mild really but in the smaller under 1 litre engines, if you manage to get the combo right they seem quite good, but not so much on larger capacity A series engines. So 60 at the crank should be around 50rwhp You'd have to be happy with that-- |
| William Revit |
| If you want something else to "over think", a long time ago I used one of those phone accelerometer apps to calculate the power curve for my VW TDI. I don't recall which one now but I seem to remember it came out about right vs. manufacturer spec. Procedure was to attach the phone firmly to the car, do a 2nd gear run from rolling start to redline then declutch and coast down so that it could estimate drag losses. |
| AdrianR |
| Took Sprite for a short run. Definitely bit of a stutter at 2-2.5k revs and no load. Can also feel it a bit starting off - I think.
Other than that seems to drive ok and is useable. It’s funny as can’t remember exactly what it was like before. Had bit of a look at the engine and there was no oil in the carb piston dampers! Put some in but made no difference. Car is still drivable, but I keep looking for problems! Plan to take car back next week, probably Thursday, to get it sorted. Just a pain being 30 miles away but couldn’t find anywhere closer. Hopefully he can sort it. Still can’t get my head round why the timing was so far out. Guess just a difference in the modules - mind you I would have thought they would have all been the same or there abouts the fact it was just a direct replacement- obviously not! Once this is sorted then still need to get the angle drive fixed for the speedo. Got a new quill pin but don’t know how to lock it in the gear, it’s seems a very loose fit. Something else to worry about! |
| Les Robinson |
| Does it need to be 'locked' into the gear, maybe just stick it there with some grease and fit it to the gearbox, it can't go anywhere. |
| William Revit |
| The quill is square but the hole is round. Quill is quite a loose fit and won’t drive the gear. Don’t know how the original was locked in place but was very tight. Looks like the quill was fitted into a sleeve that is stepped and the gear pressed onto it. |
| Les Robinson |
| Went for a walk this morning and was thinking (overthinking!!) about the bit of a stutter I can feel under little to no load. According to the man it’s a fuel issue. I am planning to take the car back next week (R E Performance in Bury) but thought could it be better to just cut my loses and go somewhere else, better, but where? Surely there must be a good engine tuner near Preston . So come on, some recommendations please. |
| Les Robinson |
| Les, for your square peg in a round hole problem: melt a bit of plastic. Poor it into the hole and then whilst still soft, pushed the end of the quill into it and allow to cool. You could do the same with epoxy, but it would probably stick to the quill and glue it in so tightly it wouldn't come out again. |
| GuyW |
| Or hot glue gun, but this might have too much "give" when running against a warm/hot gearbox? Though might be useful for testing... |
| Tim C |
| Maybe, in addition, something like the straight part of a big split pin to fix in position, like a key? Not sure how loose it is in the round hole... |
| Tim C |
| I was initially thinking Araldite or I have some metal epoxy putty type stuff. |
| Les Robinson |
| Perhaps the epoxy putty would work if you put oil or grease on the quill to stop it actually sticking to the epoxy? I'm assuming you would want to be able to dismantle it again in the future? |
| GuyW |
| I guess it’s good to be prepared for dismantling it again - just in case!
Been looking to see if there any tuning firms close by, save me having to drive to Bury again - about 30 miles away. Found Weldbank Garage in Chorley, they have a rolling road, only 5 miles away. I know it’s highly unlikely but has anyone any experience with them? The place in Bury gets good reviews but it’s just a pain if I need to keep going back. Started car earlier and for the first few minutes doesn’t feel right, then it goes ok. Previously it was fine from the very start. |
| Les Robinson |
| Sounds a bit like he might be set up a tiddle lean, although having said that ,when they're setup right you would need some amount of choke for a little while from a cold start---some of these places try to get the idle mixture leaned out like modern cars ---doesn't work. Have you tried the mixture using the lifting pins on the carbs---tried and true method |
| William Revit |
| Les, are you going to Grange? Show field or general car park? Might I see you there? |
| GuyW |
| Hi Guy Yes at the car show. White Sprite 438 XLG What car are you in? |
| Les Robinson |
| Iris blue in public car park Just arrived |
| GuyW |
| Pictures Guy(s). It's gratuitously obligatory. 😉😃 |
| anamnesis |
| My Mk2 Sprite Les ![]() ![]() |
| Les Robinson |
| We had 6 cars from the Midget and Sprite club at Grange over Sands. Two Frogeyes One Mk3 My Mk2 Plus two MGB’s Lots of lovely cars. Weather not brilliant. Met Guy which was nice. ![]() |
| Les Robinson |
| I’ve just picked up on this. Les omitted to tell me that the chap he was talking to for quite some time was Guy Weller until after he had left. I was sitting in my deck chair next to Les’ car. My car was the Green mk3. It would have been nice to have met you Guy after all the years we have been communicating on the BBS. I did however, see your Frogeye in the public car park. Very nice indeed. Ah well, maybe next time. 🤔 Bernie. |
| b higginson |
| Sorry Bernie. I was a bit confused as to who belonged with which car, and who was who! Les introduced himself and I was expecting him to be there anyway. And I am better at identifying and remembering cars than their owners!
So yours was the dark green MK3 car with the immaculate deep shine paintwork? I knew Les was coming but didn't realise there would be a MASC NW Area contingent. Had I known I might have arranged to join your little group though I missed the entry cut off date. Hence relegation to the public car park! The NW Area is so huge I actually qualify as resident in the northern reaches even though I never manage the extended trip down to the regular meetings. |
| GuyW |
| Booked my Sprite back in with R E Performance in Bury, a week on Thursday, to try and get engine running properly. I am not building my hopes up though. The annoying thing is they were highly recommended by Mini Sport.
So as mentioned earlier I found Weldbank garage in Chorley, but they get a few bad reviews. Now found Pro Tech Performance in Clifton, just north of Preston. I have no experience of them but they get good reviews. They also make a point of dealing with classic cars. Ultimately by far the best place to go is Peter Burgess, I have one of his modified heads. Biggest problem being he is over 2 hours away. But if that what it takes to get the job done properly! Will sleep on it and hopefully make a decision tomorrow. It’s driving me nuts- good job I don’t overthink and worry about things! |
| Les Robinson |
| Les, how are the dizzy spindle bushes? Is there much lateral play. I'm wondering if at slow speeds the spindle runs straight and as revs increase it begins to spin outwards, increasing the points gap. So the gap could be closing down too tight at low revs. That would make it stumble. |
| GuyW |
| Hi Guy No lateral play at all, got electronic ignition. According to the man at R E Performance it’s a fuel issue, just needs tweaking. I’m just not happy he didn’t get it right first time. In fact after tuning I was driving home, didn’t feel right so went back. He had another fiddle but still not right. Don’t feel very confident he will sort it next time. Car is drivable but just not right, got to Grange over Sands and back ok. |
| Les Robinson |
| Les, What you mean a fuel issue ? to me that is not enough fuel arriving as opposed to a carb/mixture issue ? Malc |
| Malc Gilliver |
| Malc Must admit, to me it feels like not enough fuel. |
| Les Robinson |
| when its hesitating at low revs, does addition of a little choke make any difference? |
| GuyW |
| Not tried that |
| Les Robinson |
| Les, have you tried checking the idle mixture using the lift pins. If that's ok then it's most likely a carb balance issue at slight throttle, you could check that the throttle linkage is opening both the throttles at exactly the same time- that's adjustable in the linkages but make sure both idles are matched before adjusting the linkage---It sounds like it's something they've done, adjusted, stuffed up, so should be able to be tuned out.
earlier you mentioned they found you had mismatched carburettors and they modded one---do you know what they were doing there and how they modded the carby. willy To be honest they've had two goes already really and going back for a third go----I'd be tempted to pull the pin,cut your losses and book in, pack your sandwich and head off to Alfreton for a drive to get Peter to sort it. |
| William Revit |
| Spoke to Peter Burgess, the soonest he can fit me in is 5th October! So will go back to Bury next week and see how it goes. Then if any further problems will book in with Peter. Off to Mathewsons live in Harrogate next Friday so ideally wanted it done for then. But as it is will still get me there and back. |
| Les Robinson |
| Les,
I used to work at SU - although I did oil pumps, not carbs ! I do have some of the original Su Carb setup instructions as a PDF. Can email them - firstname at secondname dot com Malc There is a Des Hamill book - about tuning carbs, but tbh the more I read the more it is likely to be the basics. 1 - take the float chamber tops off and check with a screwdriver the bottom is not full of white gunge. 2 - while the float chambers are off invert and check the floats are at the same level 3 - take the dashpots off and measure with a caliper how deep the jets are set from the bridge 4 - check that as the throttle is moved both butterflies open at the same time 5 - run the car see how she goes then stop the car and kill the engine- don't let it drop to idle and check the colour of the plugs- see haynes manual for the colour chart - remember to check at least two plugs - 1/2 and 3/4 as that will tell you if the carbs are set different |
| Malc Gilliver |
| Malc Email is:- (later removed) Thank you very much. |
| Les Robinson |
| If you edit and delete that email I would, or you might get spammed |
| Malc Gilliver |
| How do I delete it? |
| Les Robinson |
| 10/15 min time out window. I have sent you three emails - with a fourth accidental empty one |
| Malc Gilliver |
| Apologies for the hijack. Malc Interested in your SU connection. Do you mind if I email you? |
| Dave O'Neill 2 |
| Malc Got the emails. Very interesting. Thank you |
| Les Robinson |
Mention of S.U. Only cost 8/- (shillings).![]() |
| Alan Anstead |
| Alan, I included that as a PDF Dave Fine by me if you read the message to Les you'll see my email addy Mal |
| Malc Gilliver |
| Les - If you feel the need to remove your email address, you can contact Mike and he'll fix it--I've found him more than helpful in the past where he's corrected my self inflicted boo boo's that I didn't want left on public display. willy |
| William Revit |
| Tis freely available. https://share.google/qlvYkOyqEID0AGCzd |
| anamnesis |
| Email address now removed, wish getting my car tuned properly was that easy. I wonder if Mike knows anything about tuning SU’s! |
| Les Robinson |
| I don't know if those links are the same but su, and the later Burlen site, did a very detailed step by step guide for setting up and tuning these carbs. And specific for the different applications. But do follow the process through as the instructions. It's very easy to dip into doing adjustments out of sequence or as a one off and it doesn't work out so well. |
| GuyW |
| Will wait and see how it is after going back to R E Performance in Bury on Wednesday. Don’t really want to fiddle with it myself just yet in case I cock it up prior to going to Mathewsons live end of next week. As it is it’s drivable but just not right. |
| Les Robinson |
| Les, You said the carbs were not a pair and he 'tweeked' them. Worth checking both pistons drop at the same speed with a nice clunk onto the bridge. Miss matched springs, dampers ? It wont alter anything but just eliminate a variable. |
| richard b |
| I'm reminded that the Italians, at least some, had trouble with the SU carb tuning and as a result Weber produced a single choke side-draught carb which was a direct replacement for the SU HS1, I don't know whether they did them for the larger versions. I've only ever seen 2 and those were fitted to a frogeye that came over for an International Healey celebration some years back. The frogeye was from sunny southern Italy and totally original apart from the carbs. I haven't found out what they were but long out of production 30+ years ago but spares were available as they used many common parts from other Weber carbs. |
| David Billington |
| I expect it was one of these or similar https://www.carbparts.eu/en/exploded_view/WEBER_26_OC_10 |
| David Billington |
| Les--At least the cause of your engine cutting out appears to have resolved itself since the new ign. module was fitted----that's a positive. If this dyno guy doesn't come good, don't panic ,we'll get you sorted on here if you want to have a crack at it yourself. Do you know what the difference was in your two carbs and what they did to 'fix' it willy |
| William Revit |
| He was telling me that the pistons were originally different , one had a fixed needle and the other a spring loaded needle? The spring one had previously been modified to now have a fixed needle so both should effectively now be the same. This must of been done before I got the car 36 years ago. The mod he did - the piston that was originally the spring one had a small grub screw on the bottom face, this was sticking proud a tiny bit so he filed it down so both pistons would now go down to the same level. The fixed needle one had no grub screw. I think that’s what he was telling me, will double check on Wednesday.
The small grub screw must have always been there though and to my knowledge never caused an issue in the past, at least not that I am aware of. And the car had always run fine. As I said, will ask him some questions on Wednesday and try to establish what the exact cause of my issue is. |
| Les Robinson |
| Les, my guess is a slight intake leak - wear on one or both butterfly spindles when in that slightly open low revs position. Gives a slightly weakened mixture and the stutter. That's why I asked if giving it a little choke when it faltered improved it at all. It wouldn't show up at higher revs either because the wear is only on one part of tge spindle circumference, or mire likely that the amount if air leaking in is small compared to a wider throttle opening so the mixture strength is better balanced.
Slight spindle leaks can be temporarily 'fixed' with vasaline or rather longer lasting with silicone. Simply replacing the brass spindle does a pretty good job as a long term repair although an engineer perfectionist would re-bush the carb body! There is a DIY process to rebushing described in detail on the ChicagolandMG website. Or whatever its called ! |
| GuyW |
| Guy, That sounds a good suggestion, I have worn spindles and the car doesn't like very low throttle at or near idle, so I just change down and rev it ! Les, Does the rolling road have a lambda sensor ? That might show the mixture leaning out as you go from idle, with a very gentle acceleration and then richening up and the air mass increases, in effect hiding the very small leak of the spindles Mal |
| Malc Gilliver |
| The slight stutter was only there after the rolling road session, wasn’t there before. Carbs were a bit rich , plugs were always black and sooty, so he has changed the needles. Maybe it’s too weak now? |
| Les Robinson |
| If he's changed the needles, it sounds like he's picked the wrong profile. |
| Dave O'Neill 2 |
| That’s what I think. Anyway hopefully he can sort it next week. |
| Les Robinson |
| A previously slightly rich mixture could well have masked any slight spindle leak, making it run more evenly |
| GuyW |
| Will have a chat with the man on Wednesday to discuss any possible issues and will mention potential spindle wear. |
| Les Robinson |
| Les, Lift the bonnet and move the spindles, if they move you have wear.. Check the front carb against the rear just so you have a feeling of the comparative wear Mal |
| Malc Gilliver |
| This Guy? https://chicagolandmgclub.com/ ![]() ![]() |
| anamnesis |
| But no need at all to subscribe/join. Here's a link. https://www.chicagolandmgclub.com/techtips/general/545.html And the PDF too. 👍 Back in 1984, a phrase was coined. Information wants to be free. ![]() |
| anamnesis |
| Les--to me it sounds like he might have just set it up too lean at idle--some of these dyno guys tend to like lean idles for some weird reason but you can't set these old girls up like a modern car--it'd be interesting to get some figures off him when he's done. I'd guess he's using co for measuring.
Idle needs to be around 4.5co def. no less than 4 for best reliable idle and low speed performance. It'd be interesting to know what needles he went to, yours will need to be a tiddle richer than std. mainly because of those nice air filters breathing better than std. There's nothing wrong with converting to solid needles, you can get conversion kits but normally they use a different sleeve/needle mount and a longer different holding screw from the side in the original hole. Have struck a needle mod like yours on a mates mini with a single 1 3/4 on it--It was running slightly rich- The piston was being held up a tiddle just like yours which made it run lean at idle and when the mixture was richened at idle to compensate then the whole range was rich---Wasn't until I decided to do a full pull apart of the carb that i saw the pesky little screw in the bottom holding the needle holder in place was poking out probably 1/16" or so---just enough to be a pain |
| William Revit |
| According to the test results, at idle its 2.8co!! |
| Les Robinson |
Here is list of results, must admit don’t understand them.
![]() |
| Les Robinson |
| Looks like he's on around(average)5.5%-6% co on full load so that's on the money--roughly 12.5:1 afr but down the bottom of the list he's settled on 0.972%co (14.4 afr) for something--IF that's idle mixture it's way too lean, and if it's light throttle cruise it's borderline.
In all fairness it looks like he knows what he's up to testing and recording---He'll fix it, but yeah probably just a idle mixture/balance issue . Something there though--ignition timing---looks like he's got that on 8 deg. That's probably a bit low- With a std dist. if you set it at 8 static then start up it jumps to 10+ as soon as it starts. If he's done it with a strobe(timing light) at 8 idling it won't be enough specially with a modded camshaft as you have. I'd be giving it a try at 12-14 idling with a strobe, it'll take that ok. might be worth a subtle mention while you're there, just to bump it up for a try. willy |
| William Revit |
| IF the idle is 2.8%co then that is about 13.4:1 afr--it's ok but would be a better, more stable idle into the high/mid 12's |
| William Revit |
| Relooking at his figures I'm thinking he's on 0.972%co and the 287 is ppm HC----- 287ppm is fairly good for a little engine like this. I still think the co is too low at 0.972% 'IF' that's the idle spec. |
| William Revit |
| Thanks Willy. I will have a chat with the man on Wednesday and hopefully he can sort it. It’s just a bit annoying the fact I have to go back. |
| Les Robinson |
| Took car back to R E Performance today for retuning.
I mentioned about Willy’s comments regarding timing and co value at idle. To be fair the man, Ken, did listen although he had a counter argument. Anyway, he had another look at the problem and ultimately moved timing from 8 to 12 + deg and increased the co at idle to make it slightly richer - don’t know by how much though. Car drives much better, the low rev stutter has gone. Not sure about the idle smoothness but to be honest can’t remember what it was like before. Plus I am now looking for problems!! As a tuning company they must be good though judging by the cars they are working on - AC Cobra, Porche, Jaguars, Mercs, MGB’s, Stags etc, and of course a fantastic looking Sprite. However, if you went past the place you would think, ‘what a sh*t hole’, abandoned cars outside and some real wrecks. Even though car is running better I am still debating whether to book in with Peter Burgess for a tune up! |
| Les Robinson |
| Make a holiday of it Les. Let the KOTCP choose a hotel or two and you link them with some nicely selected road routes that include Alfreton as an interim stop over. |
| GuyW |
| Les. With the Swift tune cam you have I would imagine the idle to be a bit lumpy. My Kent 266 is with the advance is at 12 degrees.., but runs swell once off idle. Bernie. |
| b higginson |
| Booked in with Peter Burgess for 28 September. I will feel much happier if he does the tuning.
Back to head gasket, emailed Victor Reinz (Dana) a while ago about re torque procedure. Finally got a reply., to be fair the chap was on holiday. After initial re torque after getting hot and cooling overnight- I told them that’s what I had done. They recommended that after 100km (60miles) then re torque to 54 Nm (40lbs ft) but do not back off the nuts first, just apply final torque. Well I’ve done about 500 miles now, guess there is no problem doing a re torque (without backing off the nuts). |
| Les Robinson |
| Had engine tuned by Peter Burgess. Apparently it was running a bit rich. I did check the plugs day before and they all looked fine though. Anyway he changed the needles, tweaked the timing and after the tune up both the torque and power have increased. So good news.
What was odd, and bothering me, before I set off on what was a 3 hour journey to get there. I needed some petrol so set off then after a few hundred yards the engine was missing a bit and slight splutter. Got fuel then went back home to check plugs ( no idea why but seemed a good idea) taking no1 plug out it completely broke in two! Had I cracked it the day before? Although engine was running fine initially. Replaced it and car ran fine. Did 260 miles getting there and back including time on rolling road. What is bothering me though, is the replacement electronic ignition playing up!! I guess only time will tell. Driving home I went a different way, all motorway. For most of it was cruising at 70mph, and in the sunshine which was nice. Why is nothing ever straight forward!! |
| Les Robinson |
| Glad to hear you have had success ! I had my old engine tuned by Peter and it made such a difference, I have rung and emailed this year about a session on my new engine, but heard nothing back, not sure if they are overloaded. I also checked my plugs this week and snapped one ! Mal |
| Malc Gilliver |
| Hi Mal I think Peter is generally very busy. When I first contacted him was looking at 6-7 week wait. Only got in when I did because he had a cancellation. Normally he is good at replying to emails, have you got correct address - info@burgesstune.co.uk Les |
| Les Robinson |
This thread was discussed between 09/07/2026 and 03/10/2026
MG Midget and Sprite Technical index
This thread is from the archive. The Live MG Midget and Sprite Technical BBS is active now.