Welcome to our resource for MG Car Information.
MG Midget and Sprite Technical - misfire
| hi i own a 1968 sprite which has a bad misfire after standing for a month or so i have tried removing each ignition lead in turn as the engine is running and on removing no 1 2 and 4 the engine idles a lot rougher than before but when i remove no 3 lead it makes no difference at all i am getting a good spark from that lead and i have also tried a replacment spark plug which i know to be in working order hope someone can help me out on this one |
| mick b |
| Have you tried a compression test? Could be a valve problem on number 3. |
| Dave O'Neill 2 |
| Mick, If you don't have a compression tester, then remove the rocker cover and turn the engine slowly and watch to see that the valves all open and close fully. Especially check that the valves on #3 cylinder are not sticking open. If the engine has been stopped with one of cylinder #3 valves in the open position, it could have gained a slight mount of condensation rust on the valve stem during the cold damp weather, causing it to stick. Guy |
| Guy Weller |
| Mick. Just went through this, last week, for a non-firing number two cylinder. Root cause of the problem was a bad distributor cap--carbon bush had disintegrated on the Lucas brand cap. Cylinders two and three run leaner than cylinders one and four due to the design of the cylinder head--cylinders two and three share an exhaust port and the incoming fuel charge can be diluted because of this. Thus, a minor air leak will show up first on cylinders two and three. Spray some carb cleaner, or WD-40 around the intake manifold and the carbs to see if the sound of the engine changes as the liquid makes a temporary seal. If so, check for loose connections or a bad gasket(s). Replacing a suspect spark plug with a known good one will not tell you anything if the spark plug lead is the problem. Swap leads between cylinders one and two and see if the problem moves to cylinder one. If so, bad lead is the problem. There is information on testing spark plug leads and on doing a compression check on my website, www.custompistols.com/ if you should need it. A compression check is, always, a good first step in the troubleshooting process. Les |
| Les Bengtson |
| HI well thanks to every one for your ideas tried changing leads and dist cap but has not made any difference also tried squirting wd40 onto carb to manifold joint and menifold to engine joint but again has not made any difference also removed rocker cover and checked to see if the valves on no 3 cylinder were seating properly which they seem to do i also checked all valve gaps were correct which they are i then carried out a compresion check and these are the figures i came up with no one cylinder tirteen and a half bar no two cylinder thirteen bar no three cylinder eleven and a half bar and no four thirteen bar could a sticking valve be the cause of the lower figure on no three and would a decoke cure the problem are would i require a replacment head |
| mick b |
| Here is a tip, for spark plug wires.... because we have to cut the end of the lead off and insert it into the cap and torque down that contact screw in the cap...which all ways result in misfiring, with in a few hundered miles Take a piece of house electrical wiring strip off the insulation so you have a the soild copper wire make it an inch to an inch and a half long, then jam it all the way into the core of the spark plug wire, then stick it into the cap, and then torque down the contact screw....it will greatly reduce misfire in the spark plug lead. prop |
| Prop |
| Prop. To the best of my knowledge, the later Sprites and midgets, at least after the very early 50's, used the Lucas 25D4 distributor. The side entry cap was required for the right hand drive cars because the steering shaft went quite near the distributor and the side entry gave a little more room, ensuring that the steering column shaft would not contact a high tension lead, perhaps damaging it and causing engine running problems. Back in the days of the copper wire coil and spark plug leads, no problem with such a system and the set screw used to both retain the end of the wire and make physical contact with the terminal. So, back in the old days, no problem. Today, if one uses the side entry cap, you can have problems such as you note. So, why use it when the later, top entry cap, set up for use with silicone/carbon fiber spark plug wires is available? All of the rotors for the Lucas 25D distributors interchange as do all of the distributor caps. Switch to the later style cap along with the more modern spark plug wire system, or, retain the side entry cap and use copper cored leads. No need to mix the two. Les |
| Les Bengtson |
| I though that Mick had identified in his very first post that he had a good spark at #3 plug which is why Dave and I believed it to be a compression related fault. Mick has now checked the valves are not sticking and are adjusted correctly. The compression test figures of 192/185/165/185 (converting Bar to PSI because I understand it better) are not bad but definitely low on #3. But was this compression taken with the throttle wide open? The fact that #2 is OK suggests that it is not HGF in the weak area between 3 and 2 Slightly reduced compression could be a broken ring - test by re-doing the compression check with a small teaspoonful of oil in the cylinder. Or it could be a burnt valve. That said, compression at 165 should not cause a bad misfire anyway. So maybe it is electrical! Guy |
| Guy Weller |
| Hey les, To my knowledge, dist. caps that take moderen carbon/silicone wires are NOT avialable for the midget, or at least not at the usaual suspects auto stors....advance, zone, napa, ect. I have gotten both types of caps, both side entry and top entry and have always had to cut the lead connector off to attach to the cap....thats why I am so happy to get a mallory duel point dist. Im using caps for 1971 1275 engines prop |
| Prop |
| BTW Mick, Have you tried starting it in a completely dark gaurage, and letting it run for a while watching the engine, I have found that vary useful in finding bad wires. prop |
| Prop |
| Hi mick, Further to Prop's suggestion to check it in the dark, I once had a misfire on a Mini engine on one dark and damp night. On lifting ther bonnet with the engine running I could see the HT current tracking down the ceramic insulator on the plug. Must have been dirt or dampness, but if you've tried another plug that's known to work, it probably rules that out. Dave P. |
| Penwithian |
This thread was discussed between 02/02/2008 and 04/02/2008
MG Midget and Sprite Technical index
This thread is from the archive. The Live MG Midget and Sprite Technical BBS is active now.