MG-Cars.net

Welcome to our resource for MG Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG Midget and Sprite Technical - Fly Off Handbrake

To modify to a fly-off handbrake on a spridget, is it merely a matter of reversing the pawl?
B P Beech

B P.

Its not just a case of reversing the pawl. Take the lever to pieces and drill another hole for the operating rod to go into the pawl side of the fulcrum point. The button spring will then be trying to lift the pawl out of the ratchet and pressing the button will force the pawl into the ratchet. I did mine some years ago and did not take any pictures at the time. So you will have to use the trial and error method of finding the right position for the new hole. Measure twice drill once, theres not enough material to get it wrong. I find it not as useful as I thought it would be.

Last year I had some new tyres fitted and when I went to collect the car it was jacked up with two blokes under it trying to unjam the hand brake. They had almost pulled it up to vertical trying to get it off. So if you do it, warn anybody doing work on the car.

Mike
M J Pearson

There's a bit more to it than that, but here is a photo of a modified pawl that would work on a B or midget along with a description of how he did the mod. http://asciimation.co.nz/pics/flyaway/
Bill Young

Thanks guys. I am very grateful
B P Beech

what is the purpose of this type E brake handle.

prop
Prop

Prop, with driving skills you can greatly decrease the turning radius. ;-)
Trevor-Jessie

Might come in handy here:

http://www.youtube.com/watch?v=3YQ8d1kacQ4
Trevor-Jessie

Is that with or without an LSD?
Same old Gary

With. Is that a kiwi badge I see? I'm sure I've been crushed by that Midget at Silverstone.
Nick

I confess, it is the same much travelled Midget.

For the fly-off, we made a thin triangular plate which attached to the pawl to relocate the rod attachement. One corner shared the pivot, second corner lined up with the old rod attachment and was secured to the pawl by a small machine screw through that hole; third corner had the new pushrod hole. The position of the latter is roughly the same distance from, but the other side of, the fulcrum and at the same distance from the ratchet. Bend the pushrod to match the new hole and there you have it.

Sorry, I'm a hopeless artist or I'd try a drawing. I'll see if I can get someone to oblige and do one for me.
Paul Walbran

Hi Paul. Super information. A sketch would be good. Many thanks
B P Beech

Couldnt you do the same thing by just holding the button down???? after all you still have to move the lever up and back down.

prop
Prop

Prop

In theory, yes. In practice, holding the button down is one more thing to get wrong in the heat of strong competition. Put another way, the fly-off handbrake frees you up to concentrate on getting the line right.

Then (of course) it is a traditional MG feature. That's reason enough in itself.
Paul Walbran

Further to what Paul said - when releasing a conventional handbrake, you have to keep your thumb on the button while you move the lever all the way down to the off position. With the 'fly-off' mod, you just let go of the lever and forget about it. Much quicker.
chris rodliffe

Prompted by Paul, I dredged through my old files and found a photocopy from ~30 years ago where I first saw the fly-off conversion described - it was from a most excellent book called 'Healeys and Austin-Healeys', Appendix 4, 'Tuning the Sprite and Midget'. I have no idea if the book is still in print.
I've posted a paraphrase of the instructions, with my comments, at
http://cr.qc1.net/mgcc/flyoff.txt
plus a scan of the diagram at
http://cr.qc1.net/mgcc/flyoff.jpeg

cr
chris rodliffe

Just read all the above, and wouldnt ot be better to just drill the brake lever to take a pin wich holds the button pressed for you?
that way you can fit the pin when 'playing' and remove it for normal parking!
Mick - nearly ready to paint

Mick
Have tried that in the past and while it works fine, on a rally you can tear your gloves to bits and then your hands!
B P Beech

When i had an MGB you could get the parts to covert to a flyoff handbrake from BL special tuning.

Not sure if they offered the same for the Midget.

Richard.
richard boobier

The adaptor plate in Chris Rodliffe's diagram needs to be about 1/16" thick - any thicker and it can cause problems with clearance on the tunnel.
Paul Walbran

One other advantage to the fly off hand brake - it is just about the best anti theft device ever invented. No one not familiar with the older MGs (MGA and earlier) can release that brake. I had friends in high school who wanted to drive my TD. Since I was under strict orders from my parents that no one else was to drive the car, I would just tell them that if they could release the hand brake, they could drive the car - no one else ever drove the car. I had a batch of the bell crank pawls (pictured in the link above) made up a couple of years ago and still have one or two left that I will sell for my cost plus postage. If anyone is interested, contact me at the e-mail address at the top of this post. It is necessary to reshape the operating rod to work with the pawl, but that is easy enough to do at home. Cheers - Dave
David DuBois

Hi Dave. How much for one of your pawls?
B P Beech

BP - You have e-mail. Cheers - Dave
David DuBois

I hate to ask the obvious question, but after studying the illistation for over 15 minutes,,,,how do you un-lock the hand brake once its in gauged????

Because just pushing the button will just force the paw into the gears, and not release it.

prop


still going back to "micks" idea, why not a 2 inch gear shift ball that could be slipped on over the botton end to hold the botton down, it could be screwed on or use a recessed set screw to hold the ball in place in order to keep the button depressed that way you dont have to reform your hand when going back and forth from gear shifter lever to hand brake.


still it is a creative idea, sorry dont mean to re-invent the wheel, but just curious.


prop
Prop

You pull the handbrake lever on a fraction more, and let go of it... hence 'fly-off'... (don't touch the button)

A
Anthony

I think Mini Spares still sell the Kit and it's very reasonable in price. I bought one a couple of years ago for the Cooper S, not sure if I didn't buy a spare for one of the Spridgets... Mmmm must check.

Mark.
Mark Boldry

thanks anthony....I never thought of that.

prop
Prop

The idea suggested above of 'locking the button in' to make the handbrake effectively fly-off has been used in makeshift form on occasion by numerous people by trying to hold it in with tape. This meets with varying success - sometimes it works, all too often the tape stretches at the wrong moment. Yes, holding it in with a pin would work, and it would overcome the problem of the driver who forgets the handbrake's fly-off and jams his thumb on the button in the heat of the moment. Personally, I like the fly-off arrangement and so, having got used to it on the car all the time, I don't suffer from thumb-on-button syndrome. I only ever touch the button when using the handbrake as a parking brake, never in a competition or when driving. But it's all a matter of what you're comfortable with.

cr
Chris Rodliffe

This thread was discussed between 31/01/2008 and 05/02/2008

MG Midget and Sprite Technical index

This thread is from the archive. The Live MG Midget and Sprite Technical BBS is active now.