Welcome to our resource for MG Car Information.
MG Midget and Sprite Technical - Bleeding clutch
| I just purchased a 1979 midget 1500. The PO replaced all hydraulics in the car. Brakes are fine, but he was unable to get the clutch to work. I have read and tried all the fixes listed in the BBS archives, but still have no clutch. I am getting pressure at the slave, it squirts out fine with no visible bubbles (after running a full quart of brake fluid through), but still cannot engage 1st gear with the car running. Is it possible he got an incorrect slave that is not compatable with the pushrod? I'm stumped. |
| J L Braga |
| Has the car stood for a while? It is quite common for the clutch plate to rust to the flywheel. |
| C Bintcliffe |
| is the slave new if not he may have tryed a rebuild and didnt hone (spelling) out the slave and the piston may still be stuck or not sliding all the way forward |
| c bullock |
| I am NOT an expert on 1500 slave cylinders. There was, however, another thread recently regarding a 1500 clutch issue that referenced the pivot for the clutch and indicated that it falls out occasionally. It is quite possible that your hydraulics are fine, but the mechanical portion inside the bellhousing is losing the motion. david "trying to be helpful for a change" Lieb |
| David Lieb |
| Yes, the car had been parked for at least 6 months. How do you free it up if the clutch disc is indeed, rusted to the flywheel? It is a new master and slave, I have the old ones. When depressing the clutch pedal with the motor running, I can hear some kind of action going on inside the bellhousing which leads me to believe it's OK internally (hoping). |
| J L Braga |
| JL, The safe way is to take everything apart. Unsafe ways include safely raising the rear of the car, warming the engine up in neutral, shutting it off, re-starting it with the transmission in 3rd gear, revving it up to 2000rpm or so, and holding the clutch down while tapping the brakes. Please note that this requires an upgrade to tripod status for your feet and it is recommended that the car be pointed towards an open field. Another option is to warm up the engine in neutral, point the car at an open off-road area, re-start it in first, get it moving and use clutch and brake to encourage the clutch disk to come free of the flywheel. I am assiduously not recommending these techniques, merely indulging in a theoretical scenario or two as a mental exercise ;-) David "I would never dream of recommending such a course of action" Lieb |
| David Lieb |
| I have had this problem a couple of times over the years, on one occaision, i tried warming the engine up, stopping it and restarting it in gear with my foot on the clutch and the hand brake on, if it fees istself the clutch operates as you would expect, but dont try facing a bick wall or the garage door !this worked once, on the second occaision the slave cylinder had seized, not experienced the pin falling out yet. Alan |
| Alan |
| As david pointed out having the back of the car lifted....BUT I,,,, understood that you had the rear of the car 3 feet up, rev it up to 2500rpm in third gear, with the clutch fully depressed and have someone kick the car over, as soon as the back wheels hit the ground dump the clutch, vary exciting to say the least and then just keep jamming the brakes and the clutch back and forth...helps to have good shocks for this. I have never tried this, but thats what I have heard on how to fix the problem. prop |
| Prop |
| I have had the clutch rust on to the flywheel a couple of times. By warming the engine and then starting it in gear you can then apply the clutch while keeping the revs up brake sharply. I have done this only for the front wheels to lock up with the car still moving foreward! A couple of attempts and the clutch freed itself,so if you can find yourself a big enough safe area this should work. There can also be a problem with a build up of wear in all of the clutch actuater parts which results in the clutch dragging. If you do have to split the engine and gearbox I stongly recomend replacing all of the pivots and bushes inside the bellhousing. Good luck Carl |
| C Bintcliffe |
| JL, if you had the front of the car elevated the bleeder valve is lower than the front of the cylinder and the air bubbles, if present, can't be expelled. I suggest putting the front of the car up, removing the cylinder from the housing and angling the bleeder valve up. Have an assistant, preferably a pretty one if available, GENTLY depress the clutch pedal slowly. Watch the piston move down, have them stop, open the bleeder and push the piston back in. Having a clear hose on the bleeder will let you see any bubbles and prevent fluid from possibly getting in your eyes. This will help expel any possible air in the cylinder. Repeat until you are satisfied the air is out and don't forget to keep the clutch master topped up! This will help get you going if air is in the cylinder. Hopefully it's not the clutch stuck to the plate but I had a car sit for much longer and the clutch didn't stick. Please let us know how you made out! |
| Clive Reddin 76 Midget |
I second what Clive has said. Having rebuilt my master & slave cylinders it was a real nightmare to bleed - as Clive mentioned, the air is trapped and can't be expelled. I managed it with an eezibleed kit and the back of the car as high as I could get it. Suddenly all the air came wooshing out, and it was fine after that. Give it a try - hope it works for you... Mark |
| MarkH |
| The pin on the pivot fell out of mine, and caused problems for some time before the problem was discovered upon removing the whole engine and tranny (for other reasons). I think you can wriggle up in there to check that the pin is in place before not trying any of the things David specifically did not recommend. --jf |
| jf Falconer |
| The last time my clutch stuck to the flywheel, with the help of a couple of hefty blokes we rocked the car backwards and forwards in gear (engine wasn't running of course) and Bingo, with a bit of a bang the clutch freed itself. Dave P |
| Penwithian |
| I'm with Clive and Mark on this one. Get the back wheels a little higher off the ground than the fronts and bleeding in situ is easy even with the cylinder in place. If you have been trying to bleed with the front of the car higher than the back (as I did 'cos I aint as slim as I used to be) you will get very frustrated before you get a good clutch. You did mention.. "I can hear some kind of action going on inside the bellhousing which leads me to believe it's OK internally (hoping)". Even with an air bubble in your slave cylinder you will get some action in the bellhousing and I would suggest that you do the easy (and safe) bits first and have a shot at bleeding once more using the 'level car' procedure before you go down the route of mechanical investigations. Adam |
| A. H. Price |
This thread was discussed between 03/02/2008 and 06/02/2008
MG Midget and Sprite Technical index
This thread is from the archive. The Live MG Midget and Sprite Technical BBS is active now.