Welcome to our resource for MG Car Information.
MG Midget and Sprite Technical - anyone installed a new weber carb
| I see the weber carb for sale from Victoria British. I have a 1979 midget with a water carb. Can you order the maual choke model and covert it? How much of a pain is this to do so? The preveous owner removed all of the polution stuff except the hook up to the water portion. Let me know if it is worth it. Thanks Mark |
| Mark Hutchinson |
| Mark, why not just locate a manual choke carb? They really aren't that hard to find, especially on Evilbay. If a water choke is set up properly they work fine but a manual is easy to operate. To save any headaches though, I'd go the manual route. See if Trevor White at British Sportscar can help you out with a used manual carb. His email is: trev1952@aol.com or call the shop at 905 727-4009 or fax: 905 727-3938. |
| Clive Reddin 76 Midget |
| Mark. Depends on whether you have to meet any emissions testing requirements or not. I am assuming you are writing about the Weber DGV carb. If so, it is much easier to tune for emissions testing than the Z-S. Beyond that, I have seen little difference in performance. The water choke on the Z-S has been a problem for many and the conversion to a manual choke has been a good solution for people who want to retain the Z-S carb. If the Z-S is in good condition, it is far less expensive to install a manual choke than to replace the Z-S with the Weber. One thing that concerns me is your comment that all of the pollution controls have been removed except the water choke. (The water choke is not a pollution control--it is part of the carb operating system.) If this is true, the charcoal cannister(s) have been removed, which is not a good idea. Air pump and related systems are not a problem, in my opinion, as I believe they only dilute the exhaust rather than provide any real pollution control benefit. Plus, the pumps go out at inconvenient time and the air injection system tends to plug up with carbon, making the system ineffective. But, the charcoal cannisters serve both a pollution control and a safety function and should, always, be retained. Les |
| Les Bengtson |
| Les, Mark's car is over 20 years old and pre 1987 therefore exempt form any emissions testing in Ontario. |
| Clive Reddin 76 Midget |
| Thanks for the response. No, I do not have to have the car E tested any longer. The charcoal canister is still in place, but the air pump was removed. I do not have a great deal of knowledge in the cars set up prior to when I purchased it. I can tell you it appears that when I purchased the car a local mechanic had done a great deal of work on the car. (good or bad) My problem is that the car, if it sits for longer than a week is very hard to start. The mechanic that sold me the car through his dealership told me to press the gas to the floor once only to set up the starting. Right or wrong it does seem to work. The car runs fine and seems to work good, but my problem is when you stop after the car warms up it is all but impossible to shut the car off with out major run on. I have to pop the clutch to get the car to shut down. This why I was looking at a new carb. You have mentioned it is easier to convert the present carb to a manual choke? how can I do this? Is there a kit I can buy? Let me know and thanks again for your help. Mark |
| Mark Hutchinson |
| Mark. The fellow who told you to press the pedal to the floor one time prior to starting does not know what he is talking about. With a carb of the Weber type, the accelerator pump will spit some gas into the venturi when this happens. The Z-S and SU carbs do not have an accelerator pump and all you are doing is opening and closing the throttle butterfly. Nothing useful is being done. Manual choke conversion kits are sold "by the usual suspects"--Moss, Vicky Brit, et al. The Little British Car Company is a distributor for several of these other companies and might offer a lower price. Run on is caused by carboned up combustion chambers, too low an octane of gasoline for that engine, or incorrect ignition timing. North American specification cars had an anti-run on valve that helped keep this problem from being a problem. Perhaps part of the "pollution control" system which has been removed. The factory workshop manual is a good place to begin understanding what you are working with, what has been modified, and what you might want to reinstall. Robert Bentley Publishing offers a reprint of the original factory manual and I find that I use it more than my Haynes, Clymer, and other manuals. Les |
| Les Bengtson |
| Mark, I'm with Les. Pumping the gas pedal doesn't do a single thing for the Z-S carb as it does not have the accelerator pump like other carbs. Have you checked the diaphragm on the carb? Mine was hard to start hot and it was the diaphragm. Yours might have a hole in it. If you email me your address, I can send you a copy of the factory manual on the Z-S carb. It really helped me understand the Z-S carb! If you're not far from Toronto, (can't recall where you are again), I can come and see what we can sort out. |
| Clive Reddin 76 Midget |
| You can get a rebuild kit for your Zenith carb that replaces all the usual "wear" items, including the diaphragm. I did mine a few years ago, and have been very pleased with the result. The carb has really ceased to be a problem area, the car runs great, and the mixture has been spot-on every time I've checked it since. Really, the only thing I did wrong with my rebuild was to convert the float valve to a Grose Jet. Bad flooding ensued, since it wasn't sealing correctly. Stay with the needle-type float valve, and you'll be fine. You really ought to read this, too: http://www.paulbunyan.net/~jasko/choke/ In fact, I printed those pages and have them stuck in my manual for a reference. This choke rebuild procedure applies to both the water and manual chokes on the Zenith. By the way, my car was converted to a manual choke by a PO, and once I'd added a proper cable and replaced the little O-ring, it's been trouble free and works great. I also know that when I set my mixture at idle, the setting will be more accurate because the choke is fully sealed, and not enriching in spite of being "closed." I agree with the posts above that running-on shouldn't be carb-related. -:G:- |
| Gryf Ketcherside |
| I have a question concerning tampering with the pollution control system. Will you get fined by "changing or altering" because of the "Clean Air Act"? I took a look at the "clean Air Act" but it seems to be addressing manufacturers issues except for the max fine of $2500 for an individuals in violation. |
| Bruce Harbison |
| Bruce. An interesting question. Here in Arizona, the conversion to the Weber DGV is an accepted modification for the late model cars originally having the Z-S carb. Our Department of Environmental Services allows us to change to a more modern carb as long as we only use a single carb. Thus, conversion to twin SUs is not acceptable, but changing over to the Weber DGV is acceptable. I would suspect that allowable changes would vary from state to state and you would, if you have emissions testing as we do, the state authority in charge of such testing would be the agency to check with. I am running the DGV on two late model MGB and my daughters 77B has the Weber on it. All pass the emissions testing requirements with no problems. Les |
| Les Bengtson |
This thread was discussed between 02/02/2008 and 11/02/2008
MG Midget and Sprite Technical index
This thread is from the archive. The Live MG Midget and Sprite Technical BBS is active now.